• L type bobbin tension gauge
  
• for industrial sewing machines
  
• for many longarm quilting machines using the "L" bobbin
  
  With the Towa Bobbin Case Tension Gauge the guess work is gone forever. This gauge allows embroiderers to consistently set accurate embroidery bobbin case tension. In just a few seconds you can verify your bobbin tension is where it should be to achieve optimum results. It's simple to use and comes with complete instructions. No setup is required. It's ready to use right out of the box.
  
  How to Use a Bobbin Tension Gauge
  Take the guess work out of setting thread tensions.
  Using thread tension gauges makes it easy to adjust both bobbin and upper tensions. It's quick, easy and will help you eliminate unsightly bobbin thread showing on top, looping top stitches and thread breaks. Your embroidery will look its best with consistent, balanced thread tensions. Here's how to use a bobbin tension gauge to take the tension out of setting tensions!
  
  Instructions for Use:
  
• Remove the bobbin case from your machine. Be sure the bobbin thread is out of the pigtail and place your bobbin case with the bobbin in it into the gauge slot. Snap the bobbin case in place.
  
• Wrap the bobbin thread around the two pulley wheels and around the plastic hook end on the gauge.
  
• Steadily pull the thread and note the reading on the gauge. This represents tension readings in grams. Correct bobbin tensions should be 180 to 220 grams (up to 250 grams when embroidering caps).
  
• Please Note: If your gauge is shown in units of 10's, the correct bobbin tensions should be 18 to 22 grams (up to 25 grams when embroidering caps.)
  
• Adjust the bobbin case spring tension screw as needed to get the desired reading.
  
  Note: The gauge needle should provide a steady reading. If you experience a bouncing, erratic reading it can bedue to a dirty or defective bobbin case.
  Tip: Slide a business card back and forth under the bobbin tension spring to clear any dirt.
  
  Once you have adjusted your thread tensions, it's always a good idea to run tests.
  
• First run a fill stitch test pattern.
  
• If you experience any top stitch looping, slowly tighten the main upper tension knob until this looping goes away (looping can also occur if your bobbin tension is too tight).
  
• Proper tensions for satin stitches should reveal 1/3 bobbin and 2/3 top thread color on the underside of the embroidery.
  
  Note: Too much bobbin showing on the underside and/or showing on the topside usually means either the bobbin tension is too loose or the top thread tension is too tight.
  
  Brother Thread Tensions PDF for All Machines
  
  Common Singer Bobbin Cases & Bobbin Case Tension: Sunday Morning Quickies September 19, 2021 by Bob Fowler

• Compact design with easy-to-read LED display
  
• Provides 12-times the measuring range of analog Towa units
  
• Measures tension of both bobbin case thread and upper thread with one compact unit
  
• Battery operated (3 AAA batteries, not included)

• Class 15 type bobbin case thread tension gauge
  
• for most mechanical oscillating shuttle home sewing machines
  
  
  With the Towa Bobbin Case Tension Gauge the guess work is gone forever. This gauge allows embroiderers to consistently set accurate embroidery bobbin case tension. In just a few seconds you can verify your bobbin tension is where it should be to achieve optimum results. It's simple to use and comes with complete instructions. No setup is required. It's ready to use right out of the box.
  
  How to Use a Bobbin Tension Gauge
  Take the guess work out of setting thread tensions.
  Using thread tension gauges makes it easy to adjust both bobbin and upper tensions. It's quick, easy and will help you eliminate unsightly bobbin thread showing on top, looping top stitches and thread breaks. Your embroidery will look its best with consistent, balanced thread tensions. Here's how to use a bobbin tension gauge to take the tension out of setting tensions!
  
  Instructions for Use:
  
• Remove the bobbin case from your machine. Be sure the bobbin thread is out of the pigtail and place your bobbin case with the bobbin in it into the gauge slot. Snap the bobbin case in place.
  
• Wrap the bobbin thread around the two pulley wheels and around the plastic hook end on the gauge.
  
• Steadily pull the thread and note the reading on the gauge. This represents tension readings in grams. Correct bobbin tensions should be 180 to 220 grams (up to 250 grams when embroidering caps).
  
• Please Note: If your gauge is shown in units of 10's, the correct bobbin tensions should be 18 to 22 grams (up to 25 grams when embroidering caps.)
  
• Adjust the bobbin case spring tension screw as needed to get the desired reading.
  
  Note: The gauge needle should provide a steady reading. If you experience a bouncing, erratic reading it can bedue to a dirty or defective bobbin case.
  Tip: Slide a business card back and forth under the bobbin tension spring to clear any dirt.
  
  Once you have adjusted your thread tensions, it's always a good idea to run tests.
  
• First run a fill stitch test pattern.
  
• If you experience any top stitch looping, slowly tighten the main upper tension knob until this looping goes away (looping can also occur if your bobbin tension is too tight).
  
• Proper tensions for satin stitches should reveal 1/3 bobbin and 2/3 top thread color on the underside of the embroidery.
  
  Note: Too much bobbin showing on the underside and/or showing on the topside usually means either the bobbin tension is too loose or the top thread tension is too tight.

• Take the guess work out of setting thread tensions.
  
• Using thread tension gauges makes it easy to adjust both bobbin and upper tensions. It's quick, easy and will help you eliminate unsightly bobbin thread showing on top, looping top stitches and thread breaks. Your embroidery will look its best with consistent, balanced thread tensions. Here's how to use a bobbin tension gauge to take the tension out of setting tensions!
  
  Instructions for Use:
  
• Remove the bobbin case from your machine. Be sure the bobbin thread is out of the pigtail and place your bobbin case with the bobbin in it into the gauge slot. Snap the bobbin case in place.
  
• Wrap the bobbin thread around the two pulley wheels and around the plastic hook end on the gauge.
  
• Steadily pull the thread and note the reading on the gauge. This represents tension readings in grams. Correct bobbin tensions should be 180 to 220 grams (up to 250 grams when embroidering caps).
  
• Please Note: If your gauge is shown in units of 10's, the correct bobbin tensions should be 18 to 22 grams (up to 25 grams when embroidering caps.)
  
• Adjust the bobbin case spring tension screw as needed to get the desired reading.
  
  Note: The gauge needle should provide a steady reading. If you experience a bouncing, erratic reading it can bedue to a dirty or defective bobbin case.
  Tip: Slide a business card back and forth under the bobbin tension spring to clear any dirt.
  
  Once you have adjusted your thread tensions, it's always a good idea to run tests.
  
• First run a fill stitch test pattern.
  
• If you experience any top stitch looping, slowly tighten the main upper tension knob until this looping goes away (looping can also occur if your bobbin tension is too tight).
  
• Proper tensions for satin stitches should reveal 1/3 bobbin and 2/3 top thread color on the underside of the embroidery.
  
  Note: Too much bobbin showing on the underside and/or showing on the topside usually means either the bobbin tension is too loose or the top thread tension is too tight.
  
  Brother Thread Tensions PDF for All Machines

• Babylock Sewing Machine Models:
  B15, B17, BL18, B21, BL16, BL22, BL200, BL500, BL702, BL713, BL722, BL1000, BL1108, BL1170, BL1400, BL1500, BL1550, BL1556, BL1750, BL2000, BL2160, BL2200, BL2400, BL2500, BL2600, BL2800, BL3500 & BL5500.
  
• Belvedere Sewing Machine Models:
  Featherlite 110 Rocket & SP-82706.
  
• Bernette Sewing Machine Models:
  410, 420, 430, 440, 715, 730 & 740E.
  
• Bernina Sewing Machine Models:
  204-213 & 317-380.
  
• Brother Sewing Machine Models:
  268, 1351, 191, 320, 360, 451, 461, 651 (Charger), 661, 666FB, 681, 741, 751, 761, 1681, 7029, 991, LS1217, LS1520, LS2020, LS2125, LS2125i, LS2720, LS2725, LS2820, LS2825, LS2920, PS1200, RS15, RS25, RS35, VX Series,VX1010, VX1020, VX1120, VX1125, VX1140, VX520, VX540, VX560, VX620, VX640, VX660, VX707, VX710, VX757, VX760, VX780, VX800, VX807, VX808, VX809, VX810, VX880, VX890, VX920, VX940, VX950, VX970, VX980, VX1100, VX1200, VX1435, PX100, PX150, PX200, PX300, XL Series, XL1351, XL1561, XL1781, XL4010, XL4020, XL4030, XL4050, XL4060, XL4040, XL2010, XL2015, XL2021, XL2022, XL2025, XL2030, XL3010, XL3022, XL3025, XL3027, XL3030, XL3100, XL3200, XL5010, XL5200, XL5232, XL5300, XL5340, XL5500, XL5600, XL5700, XL5011, XL5012, XL5020, XL5030, XL5060, XL5070, XL5100, XL5130, XL5021, XL5022, XL5031, XL5032, XL5050, XL711, XL781, XL791, XL851, XR23, XR29, XR31, XR33, XR34, XR35, XR37 & XR40.
  
• Dressmaker Sewing Machine Models:
  205, 6102FA, 7000FB, S-1000, S-3000 & SWA-2000.
  
• Dial Sew Sewing Machine Models:
  916FB
  
• Domestic Sewing Machine Models:
  1630, 1665
  
• Elna Sewing Machine Models:
  110, 120, 130, 140, 149, 150, 200, 220, 225, 230, 240, 250, 255, 255i, 410, 1010, 2002, 2004, 2006, 2100, 2110, 2130, 2300
  
• Euro Pro, Omega Shark Sewing Machine Models:
  384, 7133, 7142, 991.
  
• Home Maker Sewing Machine Models:
  2345-TW
  
• Good House Keeper Sewing Machine Models:
  555.
  
• Husqvarna Viking Sewing Machine Models:
  S140 & S160.
  
• Janome(New Home) Sewing Machine Models: 100, 105, 106, 108, 110, 2003P, 300, 3125, 344, 352, 372, 373, 393, 415, 419S, 423S, 436, 444, 446, 4612, 532, 535, 540, 541, 542, 543, 544, 545, 552, 556, 574, 592, 605, 608, 609, 611, 618, 619, 620, 622, 623, 624, 625FA, 626, 628, 632, 640, 641, 642, 655, 656A, 656B, 657, 657A, Jem Gold 660, 670, 692, 792, 808, 844, 900, 910, 920, 980, 990, 1004, 1008, 1014, 1018, 1308, 1312, 1406, 1408, 1410, 1504, 1506, 1508, 1510, 1512, 1518, 1550, 1560, 1570, 1571, 1580, 1585, 1612, 1622, 1714, 1722, 1780, 1803, 1804, 1806, 1810, 1812, 1814, 1816, 1818, 1822, 1918, 2039, 2041, 3822, ENX24, Combi, Combi-10, HF107, Schoolmate S-3015, TB-12, 200, 392, 1018S, 1022, 1304, 1306, 1310, 2003, ENX24, COMBI, COMBI-10, J3-18, J3-20, J3-24, NOV3000, NOV4000, RX18s, XL11
  
• Juki Sewing Machine Models:
  HZL-25Z.
  
• JC Penney Sewing Machine Models:
  6912, 1710, 6948A, & 7029.
  
• Kenmore (Sears) Sewing Machine Models:
  5186, 117.740, 148.12181, 148.13101, 158.321, 158.471, 158.15510, 158.1561281, 158.16250, 158.17511, 158.17530, 158.17600, 158.19131, 158.480, 385.11101, 385.11206, 385.11607, 385.11608, 385.11682, 385.12014, 385.12102, 385.12116, 385.12216, 385.12314, 385.12318, 385.12514, 385.12545, 385.12581, 385.12612, 385.12614, 385.12618, 385.12712, 385.12714, 385.12781, 385.12812, 385.12814, 385.12912, 385.12916, 385.12049, 385.15008, 385.152184, 385.15510, 385.15512, 385.15516, 385.15518, 385.11608490 & 385.1264180
  
• Montgomery Wards Sewing Machine Models:
  UHTJ240A, UHTJ1859 & UHTJ1944.
  
• Morse Sewing Machine Models:
  600, 4400, Duo-Matic, MZZ, Power Stitch & Zig Zag.
  
• Necchi Sewing Machine Models:
  108, 520, 522, 523, 524FB, 525FA, 534FA, 535FA, 536, 537FA, 537L, 538, 539, 541, 554, 574FB, 575FA, 4795, 3102FA, 3204FB, 3354, 3355, 3537, 4575, 4595, 4795, 6010FB, 6011, 7020, A709-5, 802, 3101FA, 3102FA, 3204FB, 3205FA 3537, 4575, EX1, Julia, Mira, Supernova, BF Nova, BU Nova, European, BU Mira
  
• Nelco Sewing Machine Models:
  6102FB, A-3, A-509-3, F-600, JA38, N-250B4, R-400, R-1000, R-2000, R-3000, R-4000, SZA800-L, SZA-820-L2 & ZBB-1,
  
• Pfaff Sewing Machine Models:
  139, 204, 205, 206, 207, 208, 209, 210, 211, 268, 269, 301, 521, 541, 721, 741, 1020, 1022, 1030, 1032, 1040, 1042, 4240, 4250 & 4260.
  
• Riccar Sewing Machine Models:
  601, 608, 706, 707, 777, 900, 925, 1900, 1925, 2910, 2925, 7500, 469FA, 555FA, 555FB, 555SU, 666SU, 808E, R1100, R1500, R1570, R1570FB, R1800, R1850, R1950, R200, R250, R700, R7620, REC5900, RZ108B & SZ702.
  
• Singer Sewing Machine Models:
  15-30, 140Q, 227, 228, 237, 239, 1105, 1107, 1116, 1120, 1130, 1507, 1525, 1732, 1748, 2050, 2250, 2259, 2263, 2273, 2300, 3001, 3002, 3003, 3004, 3005, 3011, 3012, 3013, 3014, 3015, 3208, 3116, 4001, 4002, 4005, 4006, 4009, 4011, 4012, 4015, 4016, 4019, 4022, 4166, 5101, 5102, 5107, 5122, 5123, 5124, 5127, 5522, 5528, 8280, 8770, 30215 & 30518.
  
• Simplicity Sewing Machine Models:
  S02, S110, S210, SL237, SL415, SL1000, SL1150, SL1170, SL1200, SL1220, SL1250, SL1270, SL1400, SL1500, SL1650, SL2507, SL4700, SL6220, SL8020, SL8130, SL8220, SL9000, SL9130, SL9150, SL9240, SW210, SW2145, SA2200 S07, S110, S210, SA1100, SA1500, SA1600, SA2200 & SW2145.
  
• Tacony Sewing Machine Models:
  S05, 301Z, 303SS, 504,514, 580, 590, 601, 603, 608,653, 663, 670, 693, 701, 703,752, 753, 762B, 762W, 763, 793FA793, FA524, FA580, FA590,FA602, FA670, FA693 & FA870.
  
• Toyota Sewing Machine Models:
  6004, SE06
  
• Universal Sewing Machine Models:
  KNS & UNL-60.
  
• Viking Sewing Machine Models:
  140, 145 (Meister), 160, 165 (Meister), 207 (Husky Star), 208 (Star), 209 (Star), 210 (Star), 211 (Star), 212 (Star), 213 Star, 214 (Star), 215 (Star), 220 (Star), 230, 350, 400, 1140, 4100, 4300, 4500 & 4700
  
• White Sewing Machine Models:
  221N, 263, 312, 463, 527, 565, 568, 620, 622, 651, 656, 664, 672, 693FA, 764, 769, 804, 816, 844, 944, 955, 970, 976, 999, 1066, 1079, 1080, 1088, 1099, 1210, 1365, 1405, 1409, 1415, 1418, 1425, 1466, 1477, 1505, 1510, 1515, 1525, 1563, 1588, 1599, 1632, 1710, 1760, 1766, 1787, 1788, 1805, 1810, 1866, 1927, 1955, 1977, 1999, 2134, 2200, 2360, 2932, 3355, 4040, 301, 305, 310, 323, 346, 500, 510, 530, 1407, 1410, 1411,1620, 1630, 1665, 1730, 1888, 1911, 1919, 1975, 3955, 4000, 4041, 4042, 4050, 4060, 4400, 5000, 4075
  
  Alternative Part Numbers Include 60415, 152, 6510, 301515201, 128582001, 406104, 647515006, JO1313-S, JO1313Z3, 81417, 81901, H71186001, 647515006, 76326, 395710-08, 176786, 177487, 176772, 176786, 177487, 176772, 402784, 76326, H71185000, 549834, 128582053, 200909107, 128582083 & 403195

• Holes on outside, both sides
  
• Inner texture helps hold the end of the thread and prevent tangling
  
  Compatible with Bernina Sewing Machine Models:
  120, 125, 130, 131, 135, 140, 145, 150, 153, 155, 160, 163, 165, 170, 210, 220, 230, 240, 440, 530, 532, 534, 600, 610, 630, 642, 644, 700, 707, 708, 709, 717, 718, 719, 730, 731, 732, 800, 801, 802, 803, 807, 808, 809, 810, 811, 817, 818, 819, 830, 831, 832, 900, 910, 930, 931, 932, 1004, 1005, 1006, 1008, 1010, 1011, 1015, 1020, 1030, 1031, 1080, 1090, 1120, 1130, 1230, 1260 and 1530 (all Activa, Aurora & Virtuosa models).This will NOT fit the Artista 730

• Class 15 metal bobbins with holes on both sides
  
• Fits most oscillating hook home sewing machines
  
• Quantity discount for pack of 25 bobbins
  
• fit all class 15 machines whether older front load oscillating shuttle or newer top drop in class 15 bobbins. Metal class 15 bobbins should only be used in front load metal bobbin cases as it may cause undue wear on top load plastic bobbin cases.

• 25 pack of plastic class 15 bobbins fit all class 15 machines whether older front load oscillating shuttle or newer top drop in class 15 bobbins. It is ok to use plastic bobbins in metal and plastic bobbin cases. Metal class 15 bobbins should only be used in front load metal bobbin cases as it may cause undue wear on top load plastic bobbin cases, but will work fine.
  
  - SINGER 15 CL
  - ELNA1500,1600,3000
  - BROTHER VX800-VX1140,XL2010-203
  - ELNA 300,1010,1500,1600,2002,2004,2006,9010
  See More below.

• This compact design bobbin winder works independently of your sewing machine.
  
• It is the first complete and easy to use unit ever made. (Finally a bobbin winder that doesn't take an industrial engineer to run.)
  
• This unit includes everything you need to wind your bobbins fast and easy.
  
• Bobbins easily mount onto a spring type spindle.
  
• It comes equipped with a clear plastic safety cover for the motor and bobbin winder to prevent accidental thread tangles.
  
• It has a built in thread stand and it has a clip mounted on the platform for easy storage of the mast.
  
• The black platform is cushioned to reduce vibration.
  
• The thread guide is adjustable so that bobbins wind evenly.
  
• The friction drive pulley shuts off automatically when bobbin is full.
  
• Includes a high speed motor and electronic foot control.
  
  -Bobbin easily mounts onto split spindle for adjustment
  -14.5" width x 8.5" length x 4" high
  -Clear plastic cover for motor and bobbin winder
  -Built in spool stand and rod can be clipped into the side of the main platform
  -Black platform with 4 leg cushions to reduce vibration.
  -Separate P60999NS-V for Viking S205-605 sewing machine bobbins
  -An adjustment lever screw can be rotated to adjust the fill level as desired.
  
  *** Won't Work For Some VIKING & PFAFF Machines.
  See Description For P60999NS-V, Or Call For Info/Details. ***

• Original Solid Metal bobbin for Bernina 950 and Tacsew 950 industrial sewing machines.
  Also Bernina 217, 840, 850, 940, 950. The only less expensive generic same size bobbins are the ones for Singer Featherweight 221.
  
  For Bernina 117, 217, 640, 640-2, 740, 750, 840, 850, 940, 950, will not work on 640 Artista Grade A, Bernina compatible, Not Bernina trademark

• For Use With: PR-600, PR-600II, PR-620, Entrepreneur™ PR-650 – New! PR600 PR620 PR650 PR1000, Babylock EMP6 BMP8 BMP9 ENT10 BNT10 Embroidery Machines.
  
  Brother Polyester Bobbin thread now supplied by Ozeki Japan, formerly by Fujix Ltd
  
  These magnetic core embroidery bobbins are the only bobbin specifically designed to sew without tension variation throughout the entire bobbin. The magnetic core, combined with advanced EB "cross-link" technology optimizes dynamic thread delivery to create consistent tension from beginning to end of each bobbin.
  
  Uniform Tension Control - The patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for check springs. Remove anti-backlash (check springs) from bobbin case prior to using the Fil-Tec magnetic embroidery bobbin.
  
  Fewer Bobbin Changes - The magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  Clean Running - Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin.
  
  High Quality Yarn - Fil-Tec uses only the finest quality, high tenacity polyester yarns to make it patented magnetic core embroidery bobbin.
  
  * Patented magnetic core creates unmatched tension uniformity.
  * Bobbin will sew to the very end without tension variation.
  * High tenacity 60wt polyester yarns.
  * Patented magnetic core embroidery bobbin.
  * Lower cost per yard based on usable yards per bobbin.
  * Bobbins come with 135yds per bobbin.

• High Quality Genuine Brother SA155 Clear Plastic Bobbins
  
• 3/8 inch deep
  
• Security notch for consistent bobbin winding
  
• 10 bobbins per package
  
  For use with the following machines:
  Brother CS-8072
  Brother PS older model drop-in bobbin machines 1250, 2200, 2300, 2500
  Brother PE 100, 150, 150V, 160, 170, 170D 180, 200, 300S embroidery only
  Brother PC 2500, 2800, 3000, 6000, 6500, 7000, 7500 8200, 8500, 8500D sew/embroidery
  Brother ULT 2001, 2002D, 2003D sew and embroidery
  Babylock comparable models made by Brother
  
  Babylock BL6150 and 6600 Sewing Machines
  Babylock Espree and BL-60E Embroidery Machines
  
  Babylock older model Ellageo, Ellure, Esante, Espire & Intrigue, not the newer model Elegante, Ellure, Esante, Emore machines which take Brother SA156 Class 15.
  
  Bernina Deco 600, 650 Embroidery Machines by Brother
  Simplicity SE1, SE2, SE3 Embroidery Machines by Brother
  White 3300 Embroidery Machine by Brother
  White 4400 Embroidery Machine
  Marie Osmond EM1 Emotions Embroidery Machine
  
  
  
  *will not fit the newer model Brother LX, LS, XL, VX, XR, CE, CS, CP, ES, SE, LB, PE, NX or NV series or Project Runway machines which use the SA156 Class 15 Plastic Bobbins

• SA156 is the same featured bobbin as Brother part number XA5539-15
  
• Also same as j4b111662 for new Brother NX, 4500D and Babylock Ellegante machines. Also same as Singer 085128.
  
  
• SA156 Bobbins are 7/16" depth, high quality clear plastic and are for use in many Brother sewing and embroidery machines. (10 pack). Please check your manual to verify which bobbin style is right for your machine.
  
  
• 10 pack of plastic class 15 bobbins fit all class 15 drop-in rotary or oscillating hook machines, whether older front load or newer top drop in class 15 bobbins. It is ok to use plastic bobbins in metal and plastic bobbin cases. Metal class 15 bobbins should only be used in front load metal bobbin cases as it may cause undue wear on top load plastic bobbin cases, but will work fine.
  
  
• Class 15J Bobbins. Are you familiar with the class 15J bobbin? This is a special class bobbin used in the Singer 7400 series of machines, as well as the Futura (CE-100) and Quantum Futura (CE-200). Do not use regular class 15 bobbins in these machines, they will cause tension problems and can damage the bobbin case. The 15J is slightly smaller than the regular class 15, and the edges have a slight curve towards the center. The part number for this bobbin is 085128.
  
  Class 15 plastic bobbins for oscillating shuttle hook machines & their removable underneath bobbin cases, fit in new model drop-in bobbin machines Brother Singer Janome Juki
  
  
• Both Singer 15J and Brother SA156 Class 15 plastic bobbins have been designed with a slight curvature on the top and bottom flanges with rounded polished edges to help prevent top thread from catching underneath the top flange and jamming machines. Only the original and older versions and generic Class 15 metal and plastic bobbins had straight level flat flanges without as much rounded polished edges.
  
  For Use With Brother Models:
  BB370, BC-1000, CE-4000, CE-5000PRW, CE-5500PRW, CE7070PRW, CE8080PRW, CP-6500, CP-7500, CS-100T, CS5055PRW, CS-6000, CS-6000B, CS-6000i, CS-6000T, CS-8150, DreamMaker™ XE VE2200, DreamWeaver™ VQ3000, DreamWeaver™ XE VM6200D, Duetta® 2 4750D, Duetta® 4500D, ES-2000, EX-660, HE-120, HE-240, HS-2000, HS-2500, Innov-ís 1000, Innov-ís 1500D, Innov-ís 2500D, Innov-ís 2800D, Innov-ís 40, Innov-ís 4000D, Innov-ís 80, Innov-ís 900D, Innov-ís 950D, Isodore™ Innov-ís 5000, LB6770 PRW, LB-6800PRW, LS-1217, LS-2125, LS-2125i, LS30, LX2500, LX-3125, LX-3125E, NX-200, NX-250, NX-400, NX-400Q, NX-450, NX-450Q, NX-600, NX-650Q, Pacesetter® PS21, Pacesetter® PS-3700, PC-210, PC-210PRW, PC-420, PC-420PRW, PE500, PE-700, PE-700II, PE-750D, PE770, PE-780D, QC-1000, Quattro® 2 6700D, Quattro® 6000D, SE-270D, SE-350, SE400, Simplicity SB170, Simplicity SB3129, Simplicity SB530T, Simplicity SB700T, Simplicity SB7050E, SQ9000, SQ9050, VX-1435, XL-2230, XL-2600, XL-2600i, XL-2610, XL-3100, XL-3500, XL-3500T, XL-3510, XL-3750, XL-5130, XL-5232, XL-5340, XL-5500, XL-5600, XL-5700, XL-6452, XL-6562, XR-40, XR4040, XR-46C, XR-52C, XR-65T, XR-7700

• Brother metal rotary bobbins
  Metal Bobbins for PQ1300/1500
  For Use With: PQ-1500S, PR-620, Entrepreneur® PR-650, Entrepreneur® PR650e
  *Including Brother PR1000 650 620 600, Babylock EMP BMP ENT, Janome MB4, Melco Amaya, and other embroidery machines that use small rotary "L" bobbins, and not large M bobbins

• 1100m black bobbin thread
  60 weight machine embroidery bobbin thread gauged for Brother® machine embroidery tension
  Strong, smooth and perfectly balanced to the needle thread
  
  
  
• For Use With: HE-240, LB-6770, Innov-ís 1200, Innov-ís 1250D – New!, Innov-ís 1500D, Innov-ís 2500D, Innov-ís 2800D – New!, Innov-ís 4000D, Duetta® 4500D, Innov-ís 500D, Quattro™6000D – New!, PC-210, PC-210PRW, PC-2800, PC-3000, PC-4000, PC-420, PC-420PRW, PC-5000, PC-6000, PC-6500, PC-7000, PC-7500, PC-8200, PC-8500D, PE-400D, ULT-2001, ULT-2002D, ULT-2003D

• For 900D, 950D, 980D, SE350, SE400, LB6770, LB6800, NS 40, NS 80, PC 210, PC 410, HS 2000 and comparable Babylock models.
  
  Compatible with Brother Sewing Machine Models:
  900D, BC-1000, CE-2000, CE-4000, CE-5000PRW, CE5500PW, CP6500, CP7500, CS-4000, CS100, CS100T, CS-6000, CS-6000b, CS-6000i, CS-6000t, ES-2000, EX-660, LB6770, LB6800, PRW, SE350, SE400 & XR-7700, XR9000
  
  Alternate Part Numbers: XF5707001, XE7560001, XC3152021, XD1118021, XD1118121
  
  *For Brother models BC1000 CE4000, CE5000PRW, CS100, CS6000, ES2000, EX660, NS40, NS80, NV900D SE270D, SE350, XL2230, XR7700, XR9000 (replaces XC3152021)
  #XC3152221
  
  * CS6000
  * CS6000i
  * CS6000T
  * CS6000B
  * CS4000
  * CE2000
  * CE4000
  * BC-1000
  * EX660
  * XR7700
  
  *Fits Brother models CE4000LCD, CS100, CS6000T, CS6000, CS6000B, CS8060, CS8100, CS8150, CS8200, NV500D, NV1000D, NV1200, NV1500D, NV2500D, NV4000D, NV4500D, NV6000D, NX200, NX250, NX400, NX450, NX600, NX650, QC1000, PE-700 II and SE270D.
  
  *Fits Baby Lock models BLCC, BLCC2, BLDC, BLDC2, BLQC, BLQC2, BLG, BLG2, BLL, BLN, BLR, BLR2, BLSR, BLSO and INT.
  
  Bobbin Case XC3153051 will fit any machine that uses bobbin case part numbers XD1118021, 81348, XC3152021, XC3152221

• For the PE 700, PE700 II, PE 750D, PE770, PE 780D, PE800, PE900 and comparable Babylock models.
  
• Overseas models Innovis 700E/750E
  
• Alternate Part Numbers: XD1855051, XD1855251, XD1855351, XD1855451
  
  Guaranteed to fit Babylock Sewing Machine Models:
  BLMR
  
  Guaranteed to fit Brother Sewing Machine Models:
  HE1, NV700E, NV700EII, NV-750E, NV-780D, PE450, PE500, PE525, PE540D, PE700, PE700II, PE750D, PE-770, PE780D, SB7050E, SB7900

• Coats and Clark Prewound Bobbins
  
• Standard Rotary L Bobbins Box of 144
  
• Cardboard Bobbins
  
• Polyester Bobbin Thread
  
• Over 100,000 Stitches of Thread per Bobbin
  
  
• Coats American is renowned by embroiderers as the maker of the finest ready-wound-bobbins in the world. Years of research and a special manufacturing process ensure that Coats embroidery bobbins perform consistently - time after time.

• Coats and Clark Prewound Bobbins
  
• Standard Rotary L Bobbins Box of 144
  
• Cardboard Bobbins
  
• Polyester Bobbin Thread
  
• Over 100,000 Stitches of Thread per Bobbin
  
  
• Coats American is renowned by embroiderers as the maker of the finest ready-wound-bobbins in the world. Years of research and a special manufacturing process ensure that Coats embroidery bobbins perform consistently - time after time.

• Coats and Clark Prewound Bobbins
  
• Standard Rotary L Bobbins Box of 144
  
• Cardboard Bobbins
  
• Trusew Polyester Bobbin Thread
  
• Over 100,000 Stitches of Thread per Bobbin
  
  
• Coats American is renowned by embroiderers as the maker of the finest ready-wound-bobbins in the world. Years of research and a special manufacturing process ensure that Coats embroidery bobbins perform consistently - time after time.

• Coats and Clark Prewound Bobbins
  
• Standard Rotary L Bobbins Box of 144
  
• Cardboard Bobbins
  
• Polyester Bobbin Thread
  
• Over 100,000 Stitches of Thread per Bobbin
  
  
• Coats American is renowned by embroiderers as the maker of the finest ready-wound-bobbins in the world. Years of research and a special manufacturing process ensure that Coats embroidery bobbins perform consistently - time after time.

APPLICATIONS

ADVANTAGES

FEATURES

• Perfect and accurate bobbin winding with no operator necessary
  
• Types of thread wound include monofilament, nylon, rayon, cotton, synthetics and embroidery
  
• Winds any type bobbin (L, G, M) with .237" of 6mm opening including HA, DB, 400W, TC, 112W and
• HSM types, embroidery metal bobbins.
  
• Ideal for sewing and embroidery thread.
  
  Lower Costs
  Less costly than pre-wounds per bobbin and no large lot purchases necessary.
  
  True Color Consistency
  Pre-wound colors can often vary noticeably which affects sewn product quality.
  
  Reduced Waste/Better Inventory Control
  An operator needs only one thread spool instead of two.
  
  All thread winding is done in a central location which ensures that the correct quantity of thread is used to do the job - NO PARTIALLY USED THREAD CONES.
  
  Cut Machine Downtime
  Increases Operator Production - operator-wound bobbins consume operator time.
  
  Guaranteed Yardage on Each Bobbin
  Operator-wound bobbins yardage varies. The F-117C helps you avoid run outs/seam repairs/more bobbin changes, seconds.
  
  Consistent Thread Tension
  Ensures smoother stitches and neater seams.
  
  Better Production Planning
  CONSEW's automatic bobbin winder lets you control the amount of thread being wound which permits better production plans.
  
  
• Only 8 seconds to wind most bobbins
  
• Hopper holds more than 100 bobbins
  
• Automatic "shut-off" system when bobbin supply or thread is exhausted
  
• No operator required
  
• Built in circuit breaker
  
• Two Thread Tension Adjustments
  
• Digital counter permits you to pre-set amounts to be wound

• Use to organize bobbins by type, fiber, color or project
  
• Each Bobbin Boat holds ten class 15 or class 66 bobbins
  
• Curved interior “hugs” bobbins securely in place
  
• Patent pending design
  
• Quantity: 3-Pack
  
• Size: 4-7/8" x 1"
  
• Length: 4-7/8"
  
• Color: Multicolor

• Use to organize bobbins by type, fiber, color or project
  
• Each Bobbin Boat holds ten class 15 or class 66 bobbins
  
• Curved interior “hugs” bobbins securely in place
  
• Patent pending design
  
• Size: 4-7/8" x 1"
  
• Length: 4-7/8"
  
• Color: Multicolor

• Our patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for backlash springs.
  
  Fewer Bobbin Changes
  
• Our magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  High-Quality Yarn
  
• Fil-Tec uses only the finest quality, high tenacity polyester yarns to make it patented magnetic core embroidery bobbin.
  
  Clean Running
  
• Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin.
  
  Made in the USA:
  
• Magna-Glide Classics are proudly produced by Fil-Tec in the United States. Fil-Tec is a strong supporter of American manufacturing.

• Clear-Glide is a high-tenacity polyester filament ready-wound bobbin.
  
• Clear-Glide is wound on a plastic sided bobbin shell.
  
• Designed for today's home sewing machines, and is the "clear-choice" for drop-in bobbin cases.
  
• Offers more stitches (or yds/bobbin) than competitive or machine wound bobbins.
  
• Works well in conjunction with thread sensors.
  
• Is ideal for embroidery, general sewing, and productivity minded quilters.
  
• Each box contains 100 loose bobbins.
  
• Two box minimum of any combination of our Clear-Glide products.
  
  Fil-Tec is pleased to announce the availability of the "Clear-Glide" bobbin. Clear-Glide is the sister product of the very successful "Magna-Glide" bobbin. Clear-Glide is a high-tenacity polyester filament bobbin wound on a plastic flanged spool. This bobbin is designed for home sewing (drop-in) machines. Clear-Glide uses the same high quality poly yarn as Magna-Glide and will provide the operator with more stitches per bobbin which results in fewer bobbin changes. Each lint-free bobbin provides uniform tension, and the plastic sides will not bend. Clear-Glide is available in style-L bobbins in white, black, and limited colors.
  
  
• Fits most standard home drop-in machines (Style L).
  
• Works great with machine thread sensors.
  
• Plastic bobbin not affected by humidity or oil.
  
• No uneven tension caused by distorted paper sides.
  
• More stitches per bobbin, saves you time.
  
• Available in a wide range of colors.

• Clear-Glide is a high-tenacity polyester filament ready-wound bobbin.
  
• Clear-Glide is wound on a plastic sided bobbin shell.
  
• Designed for today's home sewing machines, and is the "clear-choice" for drop-in bobbin cases.
  
• Offers more stitches (or yds/bobbin) than competitive or machine wound bobbins.
  
• Works well in conjunction with thread sensors.
  
• Is ideal for embroidery, general sewing, and productivity minded quilters.
  
• Each box contains 80 loose bobbins.
  
• Fil-Tec Plastic Sided Machine Embroidery Bobbins Part No: 13305
  
• Class 15 / Style A - 60wt - White
  
• Compatible With Brother SA-156 Bobbins
  
• 80 Bobbins - 135 yds/Bobbin
  

• Clear-Glide is a high-tenacity polyester filament ready-wound bobbin.
  
• Clear-Glide is wound on a plastic sided bobbin shell.
  
• Designed for today's home sewing machines, and is the "clear-choice" for drop-in bobbin cases.
  
• Offers more stitches (or yds/bobbin) than competitive or machine wound bobbins.
  
• Works well in conjunction with thread sensors.
  
• Is ideal for embroidery, general sewing, and productivity minded quilters.
  
• Contains 10 tubes, with 8 bobbins in each tube , a total of 80 bobbins
  
• Two box minimum of any combination of our Clear-Glide products.

• Please remove any circular perforated backlash spring from inside your bobbin case when using Magna Core bobbins, so they have better contact with your metal bobbin case. (Remove perforated flat backlash spring from inside metal rotary bobbin cases when using magnetic bobbins to stop the bobbin from turning after machine stops. Magnetic core bobbins need better contact with bobbin case. ).
  
• Fil-Tec's revolutionary magnetic core embroidery bobbin is the only bobbin specifically designed to sew without tension variation throughout the entire bobbin. The magnetic core, combined with our advanced EB "crosslink" technology optimizes dynamic thread delivery to create consistent tension from beginning to end of each bobbin.
  
  
• Uniform Tension Control
  Our patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for backlash springs.
  
  
• Fewer Bobbin Changes
  Our magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  
• Clean Running
  Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin
  
  Filtec 12434 L size bobbin with magnetic core. 135 yards per white bobbin with 100 per box. Magna-Glide magnetic core bobbins are the only embroidery bobbin specifically designed to sew without tension variation throughout the entire bobbin.

• Please remove any circular perforated backlash spring from inside your bobbin case when using Magna Core bobbins, so they have better contact with your metal bobbin case. (Remove perforated flat backlash spring from inside metal rotary bobbin cases when using magnetic bobbins to stop the bobbin from turning after machine stops. Magnetic core bobbins need better contact with bobbin case.)
  
  
• Fil-Tec's revolutionary magnetic core embroidery bobbin is the only bobbin specifically designed to sew without tension variation throughout the entire bobbin. The magnetic core, combined with our advanced EB "crosslink" technology optimizes dynamic thread delivery to create consistent tension from beginning to end of each bobbin.
  
  Uniform Tension Control
  
• Our patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for backlash springs.
  
  Fewer Bobbin Changes
  
• Our magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  Clean Running
  
• Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin

• Please remove any circular perforated backlash spring from inside your bobbin case when using Magna Core bobbins, so they have better contact with your metal bobbin case. (Remove perforated flat backlash spring from inside metal rotary bobbin cases when using magnetic bobbins to stop the bobbin from turning after machine stops. Magnetic core bobbins need better contact with bobbin case. ).
  
  
• Fil-Tec's revolutionary magnetic core embroidery bobbin is the only bobbin specifically designed to sew without tension variation throughout the entire bobbin. The magnetic core, combined with our advanced EB "crosslink" technology optimizes dynamic thread delivery to create consistent tension from beginning to end of each bobbin.
  
  Uniform Tension Control
  
• Our patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for backlash springs.
  
  Fewer Bobbin Changes
  
• Our magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  Clean Running
  
• Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin

• Please remove any circular perforated backlash metal disc spring from inside your bobbin case when using Magna Core bobbins, so they have better contact with your metal bobbin case.(Remove perforated flat backlash spring from inside metal rotary bobbin cases when using magnetic bobbins to stop the bobbin from turning after machine stops. Magnetic core bobbins need better contact with bobbin case.)
  
  
• Fil-Tec's revolutionary magnetic core embroidery bobbin is the only bobbin specifically designed to sew without tension variation throughout the entire bobbin. The magnetic core, combined with our advanced EB "crosslink" technology optimizes dynamic thread delivery to create consistent tension from beginning to end of each bobbin.
  
  Uniform Tension Control
  
• Our patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for backlash springs.
  
  Fewer Bobbin Changes
  
• Our magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  Clean Running
  
• Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin

• Clear-Glide is a high-tenacity polyester filament ready-wound bobbin.
  
• Clear-Glide is wound on a plastic sided bobbin shell.
  
• Designed for today's home sewing machines, and is the "clear-choice" for drop-in bobbin cases.
  
• Offers more stitches (or yds/bobbin) than competitive or machine wound bobbins.
  
• Works well in conjunction with thread sensors.
  
• Is ideal for embroidery, general sewing, and productivity minded quilters.
  
• Each box contains 100 loose bobbins.
  
• Two box minimum of any combination of our Clear-Glide products.

• Consists of Egyptian long-staple fiber which creates a high luster seam appearance.
  
• Washable and colorfast.
  
• Available in popular colors so you can spend more time quilting and not winding bobbins.
  
• Clear Plastic flange bobbin works great with thread sensors so the operator knows when the bobbin yarn is about ready to run out.
  
• Offers significantly more stitches or yds per bobbin than machine wound bobbins.
  
• Each box contains 80 loose bobbins.
  
• Two box minimum of any combination of our Clear-Quilt products.

• Consists of Egyptian long-staple fiber which creates a high luster seam appearance.
  
• Washable and colorfast.
  
• Available in popular colors so you can spend more time quilting and not winding bobbins.
  
• Clear Plastic flange bobbin works great with thread sensors so the operator knows when the bobbin yarn is about ready to run out.
  
• Offers significantly more stitches or yds per bobbin than machine wound bobbins.
  
• Each box contains 100 loose bobbins.
  
• Two box minimum of any combination of our Clear-Quilt products.

• Clear-Glide is a high-tenacity polyester filament ready-wound bobbin.
  
• Clear-Glide is wound on a plastic sided bobbin shell.
  
• Designed for today's home sewing machines, and is the "clear-choice" for drop-in bobbin cases.
  
• Offers more stitches (or yds/bobbin) than competitive or machine wound bobbins.
  
• Works well in conjunction with thread sensors.
  
• Is ideal for embroidery, general sewing, and productivity minded quilters.
  
• Each box contains 80 loose bobbins.
  
• Two box minimum of any combination of our Clear-Glide products.

• Fits most standard home drop-in machines (Class 15/A).
  
• Works great with machine thread sensors.
  
• Plastic bobbin not affected by humidity or oil.
  
• No uneven tension caused by distorted paper sides.
  
• More stitches per bobbin, saves you time.
  
• 135 usable yards per bobbin.
  
• 60 wt - good for embroidery machines.
  
• Available in a wide range of colors.
  
• Runs clean - no lint buildup

• Consists of Egyptian long-staple fiber which creates a high luster seam appearance.
  
• Washable and colorfast.
  
• Available in popular colors so you can spend more time quilting and not winding bobbins.
  
• Clear Plastic flange bobbin works great with thread sensors so the operator knows when the bobbin yarn is about ready to run out.
  
• Offers significantly more stitches or yds per bobbin than machine wound bobbins.
  
• Each box contains 80 loose bobbins.
  
• Two box minimum of any combination of our Clear-Quilt products.

• Consists of Egyptian long-staple fiber which creates a high luster seam appearance.
  
• Washable and colorfast.
  
• Available in popular colors so you can spend more time quilting and not winding bobbins.
  
• Clear Plastic flange bobbin works great with thread sensors so the operator knows when the bobbin yarn is about ready to run out.
  
• Offers significantly more stitches or yds per bobbin than machine wound bobbins.
  
• Each box contains 80 loose bobbins.

• Our patented magnetic core creates consistent delivery throughout the entire bobbin. No more interruptions for tension adjustments as your bobbin gets smaller. Magnetic core prevents backlash or over spin and eliminates the need for backlash springs.
  
  Fewer Bobbin Changes
  
• Our magnetic core bobbin offers significantly more stitches per bobbin reducing defects and increasing productivity.
  
  High-Quality Yarn
  
• Fil-Tec uses only the finest quality, high tenacity polyester yarns to make it patented magnetic core embroidery bobbin.
  
  Clean Running
  
• Advanced EB cross-link technology reduces lint and residual build-up in the bobbin case and tension spring. The result is a more trouble-free bobbin.
  
  Made in the USA: Magna-Glide Classics are proudly produced by Fil-Tec in the United States. Fil-Tec is a strong supporter of American manufacturing.

• Includes 5 bobbins
  
• Made to exact manufacturer's specifications in Germany

• Standard Rotary L Bobbins Box of 144
  
• Cardboard Bobbins
  
• Polyester Filament Bobbin Thread
  
  Please note: Tension adjustment may be required if changing bobbin thread size and brands

• One action type bobbin stopper
  
• Easy adjustment of the thread-winding volume of thread is controlled by a timer
  
• Small size and light weight
  
• The intermittent switch allows simple winding start setting
  
• High-speed four bobbins winding assures the prompt, Convention of a large volume of thread to bobbins
  
  HASHIMA HW-40C Winding Video

• Jumbo (M) Bobbin
  
• Use with: MB4S, EL940S
  

• Replacement Part, Use with: MC8000, MC7700QCP, MC8900 Horizon , MC8200 Horizon , MC9900 Horizon, EL900 eXpressive, EL860 eXpressive, Skyline S5

• Janome Original Bobbin Case designed for embroidery machines without thread cutters.
  
• Use with: MC200E, MC300E

• 10 Bobbins for DDL-8700, 8500, 8300 and earlier models of high speed straight lockstitch machines and others.
  
• Not for Upholstery machines
  
• Fit Juki TL98E

• 20 Bobbins for DDL-8700, 8500, 8300 and earlier models of high speed straight lockstitch machines and others.
  
• Not for Upholstery machines
  
• Fits All Juki TL Machines: TL98E, TL98Q, TL98QE, TL2000i, TL2010Q
  
• Fits All Janome 1600P: DB, DBX, QC
  
• Fits All Brother PQ: PQ1300, PQ1500, PQ1500S

• Includes anti-backlash circular leaf spring inside the bobbin case to prevent bobbin from continuing to turn when machine and needle have stopped moving. Must be removed when using prewound bobbins.
  
• Original Equipment Manufacturer Bobbin Case for the Juki 2200QVP and TL2200QPV-S Virtuoso Long Arm Machines.
  
  Juki Bobbin Case Fits TL2200QVP & 2200QVP-S The Juki B1837201SA0 Bobbin Case Fits Juki Models TL2200QVP & 2200QVP-S. This is the bobbin case that originally came with your TL2200QVP. This is an original Juki part.

• 50 Bobbins for DDL-8700, 8500, 8300 and earlier models of high speed straight lockstitch machines and others.
  
• Not for Upholstery machines
  
• Fit Juki TL98E

• 100 Bobbins for DDL-8700, 8500, 8300 and earlier models of high speed straight lockstitch machines and others.
  
• Not for Upholstery machines
  
• Fit Juki TL98E

• Plastic bobbins are stronger than cardboard bobbins and cleaner than sideless bobbins with a lot of adhesive that gums up bobbin cases
  
• Type L standard rotary
  
• 131 yards of polyester embroidery thread per bobbin
  
• 144 bobbins to a box-one gross
  
• Not for Class 15 Bernina, Singer & Janome ;or special Viking or Pfaff bobbin replacement.
  
• Primarily for Brother made drop-in-bobbin machines such as Simplicity, Bernina-Deco, Babylock, White and Brother/Disney embroidery machines.
  For use with the following machines:
  Brother PS older model drop-in bobbin machines
  Brother PE 150, 160, 170, 180, 200 embroidery only
  Brother PC 2500, 6000, 6500, 8200, 8500D sew/embroidery
  Brother ULT 2001, 2002D, 2003D sew and embroidery
  
  Babylock BL6150 and 6600 Sewing Machines
  Babylock Espree and BL-60E Embroidery Machines
  Babylock older model Ellageo, Ellure, Esante, Espire & Intrigue, not the newer model Elegante, Ellure, Esante, Emore machines which take Brother SA156 Class 15.
  Bernina Deco 600, 650 Embroidery Machines by Brother
  Simplicity SE1, SE2, SE3 Embroidery Machines by Brother
  White 3300 Embroidery Machineby Brother
  White 4400 Embroidery Machine
  Marie Osmond EM1 Emotions Embroidery Machine
  
  *will not fit the Brother PQ-1500s, CS, NX or NV series machines which use SA156 Class 15 Plastic Bobbins

• This compact design bobbin winder works independently of your sewing machine.
  
• It is the first complete and easy to use unit ever made. (Finally a bobbin winder that doesn't take an industrial engineer to run.)
  
• This unit includes everything you need to wind your bobbins fast and easy.
  
• Bobbins easily mount onto a spring type spindle.
  
• It comes equipped with a clear plastic safety cover for the motor and bobbin winder to prevent accidental thread tangles.
  
• It has a built in thread stand and it has a clip mounted on the platform for easy storage of the mast.
  
• The black platform is cushioned to reduce vibration.
  
• The thread guide is adjustable so that bobbins wind evenly.
  
• The friction drive pulley shuts off automatically when bobbin is full.
  
• Includes a high speed motor and electronic foot control.
  
  -Bobbin easily mounts onto split spindle for adjustment
  -14.5" width x 8.5" length x 4" high
  -Clear plastic cover for motor and bobbin winder
  -Built in spool stand and rod can be clipped into the side of the main platform
  -Black platform with 4 leg cushions to reduce vibration.
  -Separate Product P60999NS for Class 15A, Singer 66, Rotary L and Big M Bobbins
  -An adjustment lever screw can be rotated to adjust the fill level as desired.
  
  

• Fits Old Singer 66, 99, 101, 185, 192, 200, 201, 300, 327, 328, 329, 400, 401, 403, 404, 413, 416, 418, 457, 500, 503, 700, 727, 800, series 6100, 6500, 7100 and other Singer drop-in bobbin machines
  
• Fits White 8600, 8800
  
• New Singers made in Campinas, Brazil factory
  
  [SINGER] - 1200-1, 185CL, 192, 201, 240 Srs. 241, 242, 247, 248, 249, 250 Srs., 252, 257, 258, 259, 263, 285, 292, 327, 328, 329, 337, 338, 347, 348, 353, 354, 360, 362, 366, 367, 368, 401, 403, 404, 413K, 413K13, 416K, 417, 418, 457, 466, 476, 477, 478, 4825, 4828, 4830, 500 Srs. 502, 5028, 503, 5605, 66, 66-6, 714, 717 School, 99, 99-13

• Fits Old Singer 66, 99, 101, 185, 192, 200, 201, 300, 327, 328, 329, 400, 401, 403, 404, 413, 416, 418, 457, 500, 503, 700, 727, 800, series 6100, 6500, 7100 and other Singer drop-in bobbin machines
  
• Fits White 8600, 8800
  
• New Singers made in Campinas, Brazil factory
  
  [SINGER] - 1200-1, 185CL, 192, 201, 240 Srs. 241, 242, 247, 248, 249, 250 Srs., 252, 257, 258, 259, 263, 285, 292, 327, 328, 329, 337, 338, 347, 348, 353, 354, 360, 362, 366, 367, 368, 401, 403, 404, 413K, 413K13, 416K, 417, 418, 457, 466, 476, 477, 478, 4825, 4828, 4830, 500 Srs. 502, 5028, 503, 5605, 66, 66-6, 714, 717 School, 99, 99-13

• Fits Singer 66, 99, 200, 300, 400, 500, some 700, 800, series 6100, 6500, 7100 and other Class 66 drop-in bobbin machines, especially those made in Brazil.
  
• Fits White 8600, 8800
  
  
• Fits Singer models 66-6, 241, 247, 247AP, 249, 252, 263, 288, 348, 413K13, 417, 457, 502, 503, 507, 509, 513, 514, 518, 522, 527, 533, 534, 538, 543, 547, 560, 563, 588, 714, 717 School, 719, 724, 734, 774, 776, 800, 833, 834, 844, 935U, 968, 1022, 1247, 1263, 1280, 1288, 1482, 1485, 1486, 1488, 1490, 1492, 1802, 1803, 1812, 1852, 1853, 1862, 1872, 1873, 2102, 2105, 2106, 2108, 2110, 2112, 2114, 2118, 2210, 2302, 2303, 2304, 2315, 2330, 2404, 2430, 2440, 2502, 2503, 2504, 2505, 2515, 2517, 2530, 2543, 2732, 2818, 2950, 3100, 3101, 3102, 3103, 3105, 3130, 3140, 3270, 3314, 3317, 3343, 4325, 4522, 4525, 4526, 4528, 4530, 4538, 4552, 4562, 4572, 4610, 4620, 4622, 4825, 4828, 4830, 4832, 5017, 5028, 5040, 5050, 5417, 5430, 5605, 5610, 5705, 5710, 57815, 5802, 5805, 5806, 5808, 5810, 5812, 5814, 5816, 5817, 5818, 5820, 5825, 5830, 5838, 5910, 5932, 6011, 6012, 6021, 6038, 6102, 6104, 6105, 6106, 6110, 6120, 6130, 6136, 6146, 6152, 6156, 6174, 6184, 6201, 6202, 6211, 6212, 6214, 6215, 6217, 6221, 6233, 6234, 6235, 6513, 6522, 6528, 6533, 6543, 6544, 6548, 6606, 6610, 6620, 6705, 6700 Series, 7004, 7015, 7021, 7025, 7028, 7033, 7035, 7101, 7102, 7104, 7105, 7106, 7108, 7110, 7136, 7174, 7211, 7212, 8002, 8007, 8019, 8100, 8200, 8220, 8500, 8600, 8734, 8774, 9005, 9008, 9010, 9015, 9018, 9020, 9022, 9027, 9030, 9032, 9034, 9044, 9110, 9130, 9134, 9210, 9323, 9334, 9408, 9410, 9416, 9420, 9423, 9430, 9432, 9444, 9500, 9502, 9505, 9518, 9600, 9602, 9605, 9606, 9608, 9610, 9612, 9614, 9618, 9802-9836, 9936, 4622, 57817, 57820, 57825, 93220, 93234, CG500, CG550, CG590, CM17, DL17, DX14, DX-14C, FM17, FM19, FM22, HD102, HD102 & HD110., SM14.

• Metal bobbins for Singer Quantum XL-1, XL-10, XL50, CXL Sewing and Embroidery Machines.
  
• Will also fit Bernina 1630 with same Juki rotary hook system, but the low bobbin warning on Bernina may not work because it requires more slots in the metal bobbin to activate the low bobbin light sensor.
  
• Holes/Slots in the sides of the metal bobbin are for the low bobbin sensor light
  
• Does not fit Quantum Drop In Bobbin embroidery machines XL100-XL 6000

• Metal bobbins for Singer Quantum XL-1, XL-10, XL50, CXL Sewing and Embroidery Machines.
  
• Will also fit Bernina 1630 with same Juki rotary hook system, but the low bobbin warning on Bernina may not work because it requires more slots in the metal bobbin to activate the low bobbin light sensor.
  
• Holes/Slots in the sides of the metal bobbin are for the low bobbin sensor light
  
• Does not fit Quantum Drop In Bobbin embroidery machines XL100-XL 6000

• Pack of 10
  
  
• Compatible with Consew 225B, 255RB, 333RB, 399RB, Seiko LSW-8L Walking Foot Needle Feed Upholstery Sewing Machines
  
  This video shows how to adjust the hook timing on a Consew 225 industrial sewing machine. The timing procedure also applies to other machines in the same class, like Singer 111W155, Juki 562, etc.

• Big M Bobbins to fit industrial upholstery sewing machines with double capacity rotary hooks.
  
• Metal
  
• #18034
  
• Fits 206RB, Sieko, etc.
  
• Alternative Part Numbers Include 1143SU, (AC 48794B657074)

• Fits Singer 20U, Consew 2033, Artidsan 2053, Yamata 20U63
  
• Fits most high speed straight stitch and zigzag industrial sewing machines except upholstery machines
  
• Fits brother PQ1500, Juki TL-98, Janome 1600P high speed, straight stitch portable sewing machines
  
• Fits Riccar and domestic rotary machines.
  Fits Alphasew model P20U33-3.
  
  Fits Baby Lock models BL3000, BL4000, BL5000, BL7000, BLQP, EMP6, BMP6, BMP8, and Quilter's Choice Professional(BLQCP).
  
  Fits Bernina Bernette models 330, 340, 430, 440, and 1000.
  
  Fits Brother model PQ-1500 and PQ-1500S
  
  Fits Consew models 99, 103, 105, 199R, 210, 220, 230, 231, 2230 and 292.
  
  Fits Elna models 100, 101, 102, 103, 104 and 1000.
  
  Fits Juki models TL98Q, TL98QE, DDL-227, DDL-555, DDL-5530, and DDL-5550.
  
  Fits Riccar models 414, 500, 515, 525, RM540, R551, R552, 606, 650, R700, R751, 805, 888, 2600, 2950, 3400, 3600, 4001, 4003, 8400, 8500, 9150, 9160, 9600, 9700, 9800, 9900, 2800/3300, 2900/3500, 555FA, 666FA, 800R, 806/807, 808E, 906E, RE571, RE581/RE591, and RM570.
  
  Fits Singer models 115-1, 188K, 191D300A, 20U, 20U13, 20U33, 206K, 206K25, 251, 281, 306K, 306K25, 306W, 319, 319K, 491D200, 491D300, 591D200A, and 591D300A.