Backing for embroidery on caps. 1000 sheets of 3.75" x 11" backing.

Non-US Warranty: 30 days parts and labor.

Backing for embroidery on caps. 1000 sheets of 4.5" x 11" backing.

Non-US Warranty: 30 days parts and labor.

Note: I have heard great things about the Brother Flat Brim Cap Driver, but the Hoop Tech Gen 2 Cap Frame and Mounting Bracket does not work on this driver. Hoop Tech 12/13/21

The Gen 2 from Hoop Tech is the next generation HTProfessional-style cap hat frame which is designed for sewing closer to the bill than ever before.

Note: Not for Brother PR1000, PR1050X. Use for some floppy hats, the Gen2 could be used on a hat with a thinner, flexible, narrow brim, more height and less width of Sewing Area, approximately 6"Wide x 4" Height*

*Note: *Requires Purchase of EMS Hoop Tech Dream T-Bar Gauge Clamp for the Dream Cap Frame- Please Specify Machine.*Also requires the Brother Driver from the original PRCF3 Cap Equipment Box*.

For all Brother 6 needle PR600, PR620, PR650, PR650E, PR655E, PR670E, plus all Babylock 6 needle models EMP6, BMP6, Happy, Tajima, Toyota, SWF, Ricoma, ZSK

Note: The hoop sensor override bracket is not sold separately. It comes with any Hoop Tech Gen2 Dream Frame (599733 & 599734) that is sold for the Brother PR & BabyLock machines.The Override Bracket is stapled to the Gen 2 in a set of instructions. Hoop Tech

Introducing the Hoop Tech "Dream Frame" Cap/Hat Hooping Frame

This is the next generation of EMS style cap frames. It was specially designed with the larger field embroidery machines in mind like Brother and Babylock.

New “DREAM FRAME” features include:
• Backing clips to hold your stabilizer in place during framing.
• Internal retaining fingers for proper bill alignment.
• A spring steel bill retainer that sets and holds the bill angle.
• View ports to use as alignment guides during framing.
• Lighter frame design (20% less weight) than the original.
• Extended saddle for easier installation on driver.
• Open design Top Clamp.
• Large sewing field

The stitch quality of the Dream Frame is even better than the original EMS style cap frame and it’s easier to frame using the redesigned T-Bar Framing Gage Seen in the recommended accessories below:


DREAM FRAME demonstration by Hoop Tech Products:







Setting up the Gen2 on your Brother PR/Babylock machine


Important Notes:

• *The Dream T-Bar Gauge clamp is required to use this Cap Frame
  
• *You must have an existing Cap Driver from the machine manufactuere to connect to your machines.
  
• There is a metal cap that covers the machine's hoop sensor which tells the machine a Cap Frame is attached. For each sew out press the layout icon for trial run to ensure the needle will not hit the hoop while sewing.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.


Click To Download PR Drive Modification Instructions

ATTENTION BROTHER PR & BABY LOCK OWNERS:
The new “GEN 2” will turn your (6) & (10) needle machine into a REAL cap sewing machine. The new bill holding strap holds down the bill so you can get closer to the needles than ever before, for a much larger sewing field.

For PR & Baby Lock owners, the “GEN 2” comes with a specially designed override bracket that attaches to your cap frame drive bar with one of the 2 thumb screws, and allows you to sew a larger sewing field and also increases the stitching speed. (Just click here to see how easy it is to set up your machine for the dream frame)

*The maximum height you can stitch is approximately up to 4" and 5.5"- 6" left to right and as close to 1/2"-5/8" from the bill. However, we do not recommend trying to embroider to the maximum sewing areas depending on the capabilities of your machine. Sewing too close to the top of the cap or too close to the bill could compromise the quality of your stitch. A more realistic measurement would be somewhere between 2" to 2.5" high and 5" to 5.5" across without losing registration.

Non-US Warranty: 30 days parts and labor.

Note: I have heard great things about the Brother Flat Brim Cap Driver, but the Hoop Tech Gen 2 Cap Frame and Mounting Bracket does not work on this driver. Hoop Tech 12/13/21

The Gen 2 from Hoop Tech is the next generation HTProfessional-style cap hat frame which is designed for sewing closer to the bill than ever before

Note: Not for Brother PR1000, PR1050X. Use for some floppy hats, the Gen2 could be used on a hat with a thinner, flexible, narrow brim, more height and less width of Sewing Area, approximately 6" Wide x 4" Height*

*Note: *Requires Purchase of EMS Hoop Tech Dream T-Bar Gauge Clamp for the Dream Cap Frame- Please Specify Machine.*Also requires the Brother Driver from the original PRCF3 Cap Equipment Box*.

For Brother PR600, PR620, PR650, PR650E, PR655E, Babylock EMP6, BMP6, Happy, Tajima, Toyota, SWF, Ricoma, ZSK

Note: The hoop sensor override bracket is not sold separately. It comes with any Hoop Tech Gen2 Dream Frame (599733 & 599734) that is sold for the Brother PR & BabyLock machines.The Override Bracket is stapled to the Gen 2 in a set of instructions. Hoop Tech

Introducing the Hoop Tech "Dream Frame" Cap/Hat Hooping Frame

This is the next generation of EMS style cap frames. It was specially designed with the larger field embroidery machines in mind like Brother and Babylock.

New “DREAM FRAME” features include:
• Backing clips to hold your stabilizer in place during framing.
• Internal retaining fingers for proper bill alignment.
• A spring steel bill retainer that sets and holds the bill angle.
• View ports to use as alignment guides during framing.
• Lighter frame design (20% less weight) than the original.
• Extended saddle for easier installation on driver.
• Open design Top Clamp.
• Large sewing field

The stitch quality of the Dream Frame is even better than the original EMS style cap frame and it’s easier to frame using the redesigned T-Bar Framing Gage Seen in the recommended accessories below:


DREAM FRAME demonstration by Hoop Tech Products:






Important Notes:

• *The Dream T-Bar Gauge clamp is required to use this Cap Frame
  
• *You must have an existing Cap Driver from the machine manufactuere to connect to your machines.
  
• There is a metal cap that covers the machine's hoop sensor which tells the machine a Cap Frame is attached. For each sew out press the layout icon for trial run to ensure the needle will not hit the hoop while sewing.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.


Click To Download PR Drive Modification Instructions

ATTENTION BROTHER PR & BABY LOCK OWNERS:
The new “GEN 2” will turn your (6) & (10) needle machine into a REAL cap sewing machine. The new bill holding strap holds down the bill so you can get closer to the needles than ever before, for a much larger sewing field.

For PR & Baby Lock owners, the “GEN 2” comes with a specially designed override bracket that attaches to your cap frame drive bar with one of the 2 thumb screws, and allows you to sew a larger sewing field and also increases the stitching speed. (Just click here to see how easy it is to set up your machine for the dream frame)

*The maximum height you can stitch is approximately up to 4" and 5.5"- 6" left to right and as close to 1/2"-5/8" from the bill. However, we do not recommend trying to embroider to the maximum sewing areas depending on the capabilities of your machine. Sewing too close to the top of the cap or too close to the bill could compromise the quality of your stitch. A more realistic measurement would be somewhere between 2" to 2.5" high and 5" to 5.5" across without losing registration.

Non-US Warranty: 30 days parts and labor.

Note: I have heard great things about the Brother Flat Brim Cap Driver, but the Hoop Tech Gen 2 Cap Frame and Mounting Bracket does not work on this driver. Hoop Tech 12/13/21

The Gen 2 from Hoop Tech is the next generation HTProfessional-style cap hat frame which is designed for sewing closer to the bill than ever before.

"The hat hoops are GREAT! So much better to use than the ones that come with the machine, very fast and easy to hoop and put on the machine, I should have bought them sooner" Joann P, Holliday RL.

Requires EMS Hoop Tech Dream T-Bar Gauge Clamp for the Dream Cap Frame Made in USA, Also requires an optional Brother Driver from the original PRPCF1 Cap Equipment Box*

*Also Requires EMS Hoop Tech Dream T-Bar Gauge Clamp for the Dream Cap Frame Made in USA, Larger Height and Less Width Sewing Area than PR Cap Equipment, for Brother PR655, PR1000, PR1000E, and Babylock ENT10 BNT10 10 Needle Embroidery Machines.

Note: The hoop sensor override bracket is not sold separately. It comes with any Hoop Tech Gen2 Dream Frame (599733 & 599734) that is sold for the Brother PR & BabyLock machines.The Override Bracket is stapled to the Gen 2 in a set of instructions. Hoop Tech

Introducing the Hoop Tech "Dream Frame" Cap/Hat Hooping Frame

This is the next generation of EMS style cap frames. It was specially designed with the larger field embroidery machines in mind like Brother and Babylock.

New “DREAM FRAME” features include:
• Backing clips to hold your stabilizer in place during framing.
• Internal retaining fingers for proper bill alignment.
• A spring steel bill retainer that sets and holds the bill angle.
• View ports to use as alignment guides during framing.
• Lighter frame design (20% less weight) than the original.
• Extended saddle for easier installation on driver.
• Open design Top Clamp.
• Large sewing field

The stitch quality of the Dream Frame is even better than the original EMS style cap frame and it’s easier to frame using the redesigned T-Bar Framing Gage Seen in Recommended accessories below:

DREAM FRAME demonstration by Hoop Tech Products:







Setting up the Gen2 on your Brother PR/Babylock machine



Important Notes:

• The Dream T-Bar Gauge clamp is required to use this Cap Frame.
  
• Can be used with existing Brother/Babylock Driver. but it is recommended that you use the Dream T-Bar Gauge for optimum results.
  
• There is a metal cap that covers the machine's hoop sensor which tells the machine a Cap Frame is attached. For each sew out press the layout icon for trial run to ensure the needle will not hit the hoop while sewing.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Click To Download PR Drive Modification Instructions

ATTENTION BROTHER PR & BABY LOCK OWNERS

The new “GEN 2” will turn your (6) & (10) needle machine into a REAL cap sewing machine. The new bill holding strap holds down the bill so you can get closer to the needles than ever before, for a much larger sewing field.

For PR & Baby Lock owners, the “GEN 2” comes with a specially designed override bracket that attaches to your cap frame drive bar with one of the 2 thumb screws, and allows you to sew a larger sewing field and also increases the stitching speed. (Just click here to see how easy it is to set up your machine for the dream frame)

The maximum height you can stitch is approximately up to 4" and 5.5"- 6" left to right and as close to 1/2"-5/8" from the bill. However, we do not recommend trying to embroider to the maximum sewing areas depending on the capabilities of your machine. Sewing too close to the top of the cap or too close to the bill could compromise the quality of your stitch. A more realistic measurement would be somewhere between 2" to 2.5" high and 5" to 5.5" across without losing registration.

Non-US Warranty: 30 days parts and labor.

On Order! Cap Driver Assembly for Brother PR1000 and PR1050X. Works with the following cap frame: Brother PRPCFH4: Brother PRPCF1 Cap Equipment, Cap Frame Brother PRPCFH4

No tools or instructions come with just the Brother cap driver part #XF6607001 below*,
only with the purchase of complete Brother 3pc cap equipment PRCF3, PRCF5 or .PRPCF1. 
This is what parts may be needed to search for online and and order online by part number, if you need to make any adjustments in the driver on your machine. .

3mm T wrench: XC7148051 x 1
2.5mm T Wrench: XC7149051x 1
Rubber Pad: XC7150051

Non-US Warranty: 30 days parts and labor.

Note: I have heard great things about the Brother Flat Brim Cap Driver, but the Hoop Tech Gen 2 Cap Frame and Mounting Bracket does not work on this driver. Hoop Tech 12/13/21

The Gen 2 from Hoop Tech is he Gen 2 from Hoop Tech is the next generation HTProfessional-style cap hat frame which is designed for sewing closer to the bill than ever before.

"The hat hoops are GREAT! So much better to use than the ones that come with the machine, very fast and easy to hoop and put on the machine, I should have bought them sooner" Joann P, Holliday FL.

Requires EMS Hoop Tech Dream T-Bar Gauge Clamp for the Dream Cap Frame Made in USA,
Also requires an optional Brother Driver from the original PRPCF1 Cap Equipment Box*
or requires the Brother Driver from your original PRPCF1 Cap Equipment Box*

*Also Requires EMS Hoop Tech Dream T-Bar Gauge Clamp for the Dream Cap Frame Made in USA, Larger Height and Less Width Sewing Area than PR Cap Equipment, for Brother PR655, PR1000, PR1000E, and Babylock ENT10 BNT10 10 Needle Embroidery Machines.

Note: The hoop sensor override bracket is not sold separately. It comes with any Hoop Tech Gen2 Dream Frame (599733 & 599734) that is sold for the Brother PR & BabyLock machines.The Override Bracket is stapled to the Gen 2 in a set of instructions. Hoop Tech

Introducing the Hoop Tech "Dream Frame" Cap/Hat Hooping Frame

This is the next generation of EMS style cap frames. It was specially designed with the larger field embroidery machines in mind like Brother and Babylock.

New “DREAM FRAME” features include:
• Backing clips to hold your stabilizer in place during framing.
• Internal retaining fingers for proper bill alignment.
• A spring steel bill retainer that sets and holds the bill angle.
• View ports to use as alignment guides during framing.
• Lighter frame design (20% less weight) than the original.
• Extended saddle for easier installation on driver.
• Open design Top Clamp.
• Large sewing field

The stitch quality of the Dream Frame is even better than the original EMS style cap frame and it’s easier to frame using the redesigned T-Bar Framing Gage Seen in Recommended accessories below:

DREAM FRAME demonstration by Hoop Tech Products:






Important Notes:

• The Dream T-Bar Gauge clamp is required to use this Cap Frame.
  
• Can be used with existing Brother/Babylock Driver. but it is recommended that you use the Dream T-Bar Gauge for optimum results.
  
• There is a metal cap that covers the machine's hoop sensor which tells the machine a Cap Frame is attached. For each sew out press the layout icon for trial run to ensure the needle will not hit the hoop while sewing.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Click To Download PR Drive Modification Instructions

ATTENTION BROTHER PR & BABY LOCK OWNERS

The new “GEN 2” will turn your (6) & (10) needle machine into a REAL cap sewing machine. The new bill holding strap holds down the bill so you can get closer to the needles than ever before, for a much larger sewing field.

For PR & Baby Lock owners, the “GEN 2” comes with a specially designed override bracket that attaches to your cap frame drive bar with one of the 2 thumb screws, and allows you to sew a larger sewing field and also increases the stitching speed. (Just click here to see how easy it is to set up your machine for the dream frame)

The maximum height you can stitch is approximately up to 4" and 5.5"- 6" left to right and as close to 1/2"-5/8" from the bill. However, we do not recommend trying to embroider to the maximum sewing areas depending on the capabilities of your machine. Sewing too close to the top of the cap or too close to the bill could compromise the quality of your stitch. A more realistic measurement would be somewhere between 2" to 2.5" high and 5" to 5.5" across without losing registration.

Non-US Warranty: 30 days parts and labor.

PRCH3-XE2268001 Cap Driver Assembly for Brother PRS100, PR600II, PR620, PR650, PR650E, PR670E.
Works with the following cap frame, XC7477051: PRCFH2, Cap Frame B, Advanced Cap Frame

Non-US Warranty: 30 days parts and labor.

"The hat hoops are GREAT! So much better to use than the ones that come with the machine, very fast and easy to hoop and put on the machine, I should have bought them sooner" Joann P, Holiday FL.

The Dream T-Bar Gauge is basically the same as the 270 T-Bar Gauge with a few changes.

The patented HOOP TECH Framing Gage features the exclusive T–Bar Tensioning Arm.

This tensioning arm gives even the inexperienced cap framer the ability to frame a cap tight…even low profile un-constructed caps.

It’s the easiest way to stretch a cap tight!

Once you try it, you’ll be amazed at how easy it can be to frame a cap!

The Dream Frame is not included in this package. To add the Dream Frame please see the Recommended Accessories Section Below






NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

• *You must have an existing Cap Driver from the machine manufacturer to connect to your machines
  

Non-US Warranty: 30 days parts and labor.

To embroider on Santa Hats, Stockings and Shirt Cuffs I would recommend our Small Compact Back of Cap, not this large one. Hoop Tech.

Large back of hat clamp. This Easy to use back of hat clamp attaches to your cap frame driver and has the following inside dimensions: 5.5” x 2.875”

It will work with your existing cap hooping gauge and your machines driver. The optional small version of this clamp has 5.5” x 2.5” dimensions.

See Justin from Hoop Tech talk about cap frames at the Houston Virtual Quilt Festival!

Non-US Warranty: 30 days parts and labor.

2 and 3/4 inches wide by 2 1/2 inches is the size of the window. Like the slimline, we can adapt to most commercial machines including Melco, Happy, Barudan, Tajima, Toyota, Brother, Highland, Ricoma, other, etc.

The Side Clamp for Hats was designed to hold the left or right side panels on a hat and has a single cam lever that open/closes locking the clamp. The Cap Side Clamp is mounted directly to the machine driver bar (same as your cap driver). Please order the machine clamp needed with the drop down menu to the right.

Non-US Warranty: 30 days parts and labor.

To embroider on Santa Hats, Stockings and Shirt Cuffs I would recommend our Small Compact Back of Cap. Hoop Tech.

Use with Hoop Tech Pocket Framing Gauge plus the Cap Driver for your machine.

See Justin and Joe from Hoop Tech talk about cap frames at the Houston Virtual Quilt Festival!


Note this video shows the Tajima hoop which includes the Red toggle switch, the Brother compatible hoops do not have the red toggle switch.

Hoop Tech's back of cap clamp is the easiest way to embroider the back of hats when your cap driver is already installed on the machine. It features a simple clamping action, which lets you position the cap easily.

Features:

• Easy Installation
  
• Spring clips keep your stabilizer in place
  
• Use one level for locking and clamping in one step
  
• Large embroidery area
  
• Centering points for easy positioning
  
• Inside Dimensions: A little over 5 inches left to right and 2 & 1/2 inches tall
  
  Driver Sold Separately
  Will not work with every driver but will on the majority of Tajima, Brother, Melco and Toyota machines. Please specify your machine brand and model upon checkout.
  
  NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout go make sure the needle or foot will not hit the frame when it is sewing.
  
  Step-by-step instructions on lowering and adjusting the PR Cap Driver

Non-US Warranty: 30 days parts and labor.

The Pocket Clamp series are individual window clamps that were designed to hold the pocket fronts on finished dress shirts. Sewing on pocket fronts has always been a challenge due to the limited amount of space that a dress shirt pocket has. But with the smaller sewing arms offered by some embroidery machine manufacturers, like the Melco Amaya, sewing on pocket fronts has become possible with the use of the Hoop Tech Pocket Clamps.

The Pocket Clamps are made with a fixed lower window and a moveable top window that is actuated and locked with a hand tightened knob. Made entirely of stainless steel the clamps are built to last. The Clamps attach to and are run on your machines cap driver to help maximize the sewing field.

Pocket Clamps, although designed for the fronts of dress shirt pockets, are not limited to just that. Other uses include Socks, gloves, beanies, monogramming shirt cuffs, knit baby hats, collars, slippers and other applications that have limited space for an inside hoop.

Driver mounted Clamps for Embroidery on pocket fronts.
Sewing on pockets can be challenging due to lack of space but with smaller sewing arms offered on some embroidery machines, like the melco amaya, sewing on pocket fronts has become possible!

The pocket clamps have a hand tightened knob on the top that open and close the top window. These stainless steel clamps are built to last. They slide right onto your cap driver to help maximize the sewing field.

Note: not all sewing arms are created equal, so not all sewing arms will fit in all pockets and still have room to sew.

We do not currently have a pocket clamp that is compatible with Barudan machines.

Many Uses
This versatile clamp has many other uses! Other uses include socks, gloves, beanies, shirt cuff monograms, knit baby hats, collars, slippers, and other items that have limited space for an inside hoop.

Non-US Warranty: 30 days parts and labor.

Required: Must order or have the Pocket Framing Gauge for use with this attachment.

Newer 599919 has an enhanced twist handle for easier tightening. The old model 599812 had a black knob for tightening.

Driver mounted Clamps for Embroidery on pocket fronts.

POCKET CLAMPS

The POCKET CLAMP series are individual window clamps that were designed to hold the pocket fronts on finished dress shirts. Sewing on pocket fronts has always been a challenge due to the limited amount of space that a dress shirt pocket has. But with the smaller sewing arms offered by some embroidery machine manufacturers, like the Melco Amaya, sewing on pocket fronts has become possible with the use of the Hoop Tech POCKET CLAMPS.

The Pocket Clamps are made with a fixed lower window and a moveable top window that is actuated and locked with a hand tightened knob. Made entirely of stainless steel the clamps are built to last. The Clamps attach to and are run on your machines cap driver to help maximize the sewing field.

Available in three different sizes 2.5 x 3.75, 3.0 x 3.75.

POCKET CLAMPS although designed for the fronts of dress shirt pockets, are not limited to just that. Other uses include Socks, gloves, beanies, monogramming shirt cuffs, knit baby hats, collars, slippers and other applications that have limited space for an inside hoop.

Driver mounted Clamps for Embroidery on pocket fronts.
Sewing on pockets can be challenging due to lack of space but with smaller sewing arms offered on some embroidery machines, like the melco amaya, sewing on pocket fronts has become possible!

The pocket clamps have a hand tightened knob on the top that open and close the top window. These stainless steel clamps are built to last. They slide right onto your cap driver to help maximize the sewing field.

Note: not all sewing arms are created equal, so not all sewing arms will fit in all pockets and still have room to sew.

We do not currently have a pocket clamp that is compatible with Barudan machines.

Many Uses
This versatile clamp has many other uses! Other uses include socks, gloves, beanies, shirt cuff monograms, knit baby hats, collars, slippers, and other items that have limited space for an inside hoop.

Non-US Warranty: 30 days parts and labor.

Required: Must order or have the Pocket Framing Gauge for use with this attachment.

Driver mounted Clamps for Embroidery on pocket fronts.

POCKET CLAMPS

The POCKET CLAMP series are individual window clamps that were designed to hold the pocket fronts on finished dress shirts. Sewing on pocket fronts has always been a challenge due to the limited amount of space that a dress shirt pocket has. But with the smaller sewing arms offered by some embroidery machine manufacturers, like the Melco Amaya, sewing on pocket fronts has become possible with the use of the Hoop Tech POCKET CLAMPS.

The Pocket Clamps are made with a fixed lower window and a moveable top window that is actuated and locked with a hand tightened knob. Made entirely of stainless steel the clamps are built to last. The Clamps attach to and are run on your machines cap driver to help maximize the sewing field.

Available in three different sizes 2.5 x 3.75, 3.0 x 3.75 & 3.5 x 3.75.

POCKET CLAMPS although designed for the fronts of dress shirt pockets, are not limited to just that. Other uses include Socks, gloves, beanies, monogramming shirt cuffs, knit baby hats, collars, slippers and other applications that have limited space for an inside hoop.

Non-US Warranty: 30 days parts and labor.

for use with POCKET (micro) CLAMPS Sold Separately. Driver mounted Clamps for Embroidery on pocket fronts.
Sewing on pockets can be challenging due to lack of space but with smaller sewing arms offered on some embroidery machines, like the melco amaya, sewing on pocket fronts has become possible!

The pocket clamps have a hand tightened knob on the top that open and close the top window. These stainless steel clamps are built to last. They slide right onto your cap driver to help maximize the sewing field.

Note: not all sewing arms are created equal, so not all sewing arms will fit in all pockets and still have room to sew.

We do not currently have a pocket clamp that is compatible with Barudan machines.

The pocket clamp series are individual window clamps that were designed to hold the pocket fronts on finished dress shirts.

Non-US Warranty: 30 days parts and labor.

The Hoop Tech Slim Line 1 Clamping System Chassis for Janome MB4 Series is compatible with the Janome MB4, MB4N, MB4S, and Elna 940 embroidery machines. Use Hoop Tech Slim Line 1 Clamping System Chasis for Janome MB4 Series when you want faster positioning without obstacles. This Hoop Tech Slim Line 1 Clamping System Chassis for Janome MB4 Series can clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Also, the Hoop Tech Slim Line 1 Clamping System Chassis for Janome MB4 Series holds products steady, and never leaves a hoop burn. Versatile, the Hoop Tech Slim Line 1 Clamping System Chassis for Janome MB4 Series is perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.

Base Unit does not include any Windows or Frames shown, but is required to use Tubular HoopTech SAPR4, SAPR2RD, SAPR35, SAPR44, SAPR53, SAPR5RD, SAPRHSL, SAPRHSR.

Non-US Warranty: 30 days parts and labor.

Required: Must also order or have the Pocket Framing Gauge for use with this attachment.

For use with Brother PRCF3 cap driver only.

Driver mounted Clamps for Embroidery on pocket fronts.

POCKET CLAMPS:

The POCKET CLAMP series are individual window clamps that were designed to hold the pocket fronts on finished dress shirts. Sewing on pocket fronts has always been a challenge due to the limited amount of space that a dress shirt pocket has. But with the smaller sewing arms offered by some embroidery machine manufacturers, like the Melco Amaya, sewing on pocket fronts has become possible with the use of the Hoop Tech POCKET CLAMPS.

The Pocket Clamps are made with a fixed lower window and a moveable top window that is actuated and locked with a hand tightened knob. Made entirely of stainless steel the clamps are built to last. The Clamps attach to and are run on your machines cap driver to help maximize the sewing field.

Available in three different sizes 2.5 x 3.75, 3.0 x 3.75 & 3.5 x 3.75.

POCKET CLAMPS although designed for the fronts of dress shirt pockets, are not limited to just that. Other uses include Socks, gloves, beanies, monogramming shirt cuffs, knit baby hats, collars, slippers and other applications that have limited space for an inside hoop.

Driver mounted Clamps for Embroidery on pocket fronts.
Sewing on pockets can be challenging due to lack of space but with smaller sewing arms offered on some embroidery machines, like the melco amaya, sewing on pocket fronts has become possible!

The pocket clamps have a hand tightened knob on the top that open and close the top window. These stainless steel clamps are built to last. They slide right onto your cap driver to help maximize the sewing field.

Note: not all sewing arms are created equal, so not all sewing arms will fit in all pockets and still have room to sew.

We do not currently have a pocket clamp that is compatible with Barudan machines.

Many Uses
This versatile clamp has many other uses! Other uses include socks, gloves, beanies, shirt cuff monograms, knit baby hats, collars, slippers, and other items that have limited space for an inside hoop.

Non-US Warranty: 30 days parts and labor.

The Pocket Clamp series are individual window clamps that were designed to hold the pocket fronts on finished dress shirts. Sewing on pocket fronts has always been a challenge due to the limited amount of space that a dress shirt pocket has. But with the smaller sewing arms offered by some embroidery machine manufacturers, like the Melco Amaya, sewing on pocket fronts has become possible with the use of the Hoop Tech Pocket Clamps.

The Pocket Clamps are made with a fixed lower window and a moveable top window that is actuated and locked with a hand tightened knob. Made entirely of stainless steel the clamps are built to last. The Clamps attach to and are run on your machines cap driver to help maximize the sewing field.

Pocket Clamps, although designed for the fronts of dress shirt pockets, are not limited to just that. Other uses include Socks, gloves, beanies, monogramming shirt cuffs, knit baby hats, collars, slippers and other applications that have limited space for an inside hoop.

Driver mounted Clamps for Embroidery on pocket fronts.
Sewing on pockets can be challenging due to lack of space but with smaller sewing arms offered on some embroidery machines, like the melco amaya, sewing on pocket fronts has become possible!

The pocket clamps have a hand tightened knob on the top that open and close the top window. These stainless steel clamps are built to last. They slide right onto your cap driver to help maximize the sewing field.

Note: not all sewing arms are created equal, so not all sewing arms will fit in all pockets and still have room to sew.

We do not currently have a pocket clamp that is compatible with Barudan machines.

Many Uses
This versatile clamp has many other uses! Other uses include socks, gloves, beanies, shirt cuff monograms, knit baby hats, collars, slippers, and other items that have limited space for an inside hoop.

Non-US Warranty: 30 days parts and labor.

The Hoop Tech Slim Line 1 Clamping System Chassis is compatible with the Janome Brother/ Babylock PRS100, PR6 and PR10 embroidery machines. Use Hoop Tech Slim Line 1 Clamping System Chasis for when you want faster positioning without obstacles. This Hoop Tech Slim Line 1 Clamping System Chassiscan clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Also, the Hoop Tech Slim Line 1 Clamping System Chassis for Janome MB4 Series holds products steady, and never leaves a hoop burn. Versatile, the Hoop Tech Slim Line 1 Clamping System Chassis for Janome MB4 Series is perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.

Base Unit does not include any Windows or Frames shown, but is required to use Tubular HoopTech SAPR4, SAPR2RD, SAPR35, SAPR44, SAPR53, SAPR5RD, SAPRHSL, SAPRHSR.

Non-US Warranty: 30 days parts and labor.

The Slim Line “Persona” Clamping System is a redesigned version of the very popular Slim Line -1 with a compact chassis and new window shape. The Persona package includes, a new chassis with adapter and (4) window sizes. 7 x 6, 4.5 x 4.5, 3.5 x 5.5 & 2 x 2. Rail Mounted Clamping System.

Hoop Tech 599869 SlimLine Hoop Chassis is NOT available for ordering separately from this set.

The Slim Line Persona is the perfect choice for embroidering smaller difficult to hoop items such as purses, back packs and small totes.

Expand your product offerings and stay ahead of your competition! Open the world of embroidery to items that were previously impossible to sew on: leather portfolios, tote bags, heavy and thick items and more– the possibilities are endless.

Watch Justin from Hoop Tech talk about this set at the Houston Virtual Quilt Festival below!


HoopTech Clamping and Windows System Option Videos

Non-US Warranty: 30 days parts and labor.

The HOOP TECH Soccer Shoe Clamp is designed to allows embroidery on soccer shoe sides and tongues. Its exceptional grip strength will hold the shoe in place during embroidering. The clamp body is rail mounted , (it attaches directly the drive rail of the panagraph - same as a cap driver) to ensure maximum rigidity on the machine.

The window size is 2 3/4" wide by 1 1/2" deep. The window size is designed small enough to fit down into most shoe sides and still have an adequate sewing field for logos, flags, initials, names, numbers etc.

The upper and lower clamping frames have an aggressive non-slip surface to hold leather and nylon secure during sewing.

Embroidery on finished shoes is definitely a challenge. But with the HOOP TECH Soccer Shoe Clamp you will be able to sew in places that you never thought possible.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

The HOOP TECH Soccer Shoe Clamp is designed to allows embroidery on soccer shoe sides and tongues. Its exceptional grip strength will hold the shoe in place during embroidering. The clamp body is rail mounted , (it attaches directly the drive rail of the panagraph - same as a cap driver) to ensure maximum rigidity on the machine.

The window size is 2 3/4" wide by 1 1/2" deep. The window size is designed small enough to fit down into most shoe sides and still have an adequate sewing field for logos, flags, initials, names, numbers etc.

The upper and lower clamping frames have an aggressive non-slip surface to hold leather and nylon secure during sewing.

Embroidery on finished shoes is definitely a challenge. But with the HOOP TECH Soccer Shoe Clamp you will be able to sew in places that you never thought possible.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

Ships Unassembled

The Hooptech Cap Framing Stand is a stand alone work station designed specifically for framing caps. The Framing Gage mounting bar easily adjusts to the proper working height for all sizes of operators. Working at the right height helps to ensure consistent framing and reduces sore muscles and operator fatigue.

Non-US Warranty: 30 days parts and labor.

*Hoop Tech Base Unit does not include any Windows or the Frame shown, but is required to use Tubular HoopTech SAPR4, SAPR2RD, SAPR35, SAPR44, SAPR53, SAPR5RD, SAPRHSL, SAPRHSR Hoops

There are (9) different window sizes to choose from with the Slim Line 1 Clamping System. Each (3) piece window set comes with a Base Adapter window and (2) top clamping windows. One for thin fabrics and one for thicker stiffer material. All window sets quickly and easily install onto the chassis, no tools required.

Works with the Following Machines:
Brother

• PR600
  
• PR620
  
• PR650
  
• PR670
  
• PR1000
  
• PR1050
  
  BabyLock
  
• EMP6
  
• BMP6
  
• ENT10
  
• BNT10
  
  Hoop Tech is the perfect choice for embroidering smaller difficult to hoop items such as purses, back packs and small totes. Expand your product offerings and stay ahead of your competition! Open the world of embroidery to items that previously were impossible to sew on: leather portfolios, tote bags, heavy and thick items and more– the possibilities are endless.
  
  Clamping System Features:
  
• Single lever opens, closes and locks the clamp.
  
• (8) interchangeable window sizes to choose from.
  
• Mounts directly to machine drive bar for positive attachment.
  
• All metal construction, powder coated aluminum & stainless steel.
  
• The clamp automatically adjusts to different fabric thickness.
  
• Clamping action does not leave “hoop burns”
  
• Clamp stays on the machine while loading and unloading.
  
  The base unit, or Chassis, holds the two pieces (bottom and top) of the clamping Window in place with just the twist of a knob!
  
  Use Clamps when you want Faster Positioning Without Obstacles! Clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Holds products steady, and never leaves a hoop burn. Perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.
  
  The Hoop Tech SAPRB6 Small Chassic for Brother PR Series is for Brother PR and Baby Lock EMP Series Machines. Use Hoop Tech SAPRB6 Small Chassic for Brother PR Series when you want faster positioning without obstacles. This Hoop Tech SAPRB6 Small Chassic for Brother PR Series can clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Also, the Hoop Tech SAPRB6 Small Chassic for Brother PR Series holds products steady, and never leaves a hoop burn. Versatile, the Hoop Tech SAPRB6 Small Chassic for Brother PR Series is perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.
  
  Base Unit does not include any Windows or Frames shown, but is required to use Tubular HoopTech SAPR4, SAPR2RD, SAPR35, SAPR44, SAPR53, SAPR5RD, SAPRHSL, SAPRHSR.

Non-US Warranty: 30 days parts and labor.

Frames not included. Look under specials for the frames available for use with this base.
Frame Sizes Available for Add-on:

• 4.5" x 6" frame
  
• 7.5" x 3" frame
  
• 5" x 5" frame
  
• 6" x 6" frame

Non-US Warranty: 30 days parts and labor.

The Hoop Tech Slim Line 1 Clamping System Chassis for Tajima Series is compatible with the Tajima embroidery machines. Use Hoop Tech Slim Line 1 Clamping System Chassis for Tajima when you want faster positioning without obstacles. This Hoop Tech Slim Line 1 Clamping System Chassis for Tajima Series can clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Also, the Hoop Tech Slim Line 1 Clamping System Chassis for Tajima holds products steady, and never leaves a hoop burn. Versatile, the Hoop Tech Slim Line 1 Clamping System Chassis for Tajima Series is perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.

Base Unit does not include any Windows or Frames shown, but is required to use Tubular HoopTech SAPR4, SAPR2RD, SAPR35, SAPR44, SAPR53, SAPR5RD, SAPRHSL, SAPRHSR.

Non-US Warranty: 30 days parts and labor.

3" Wide x 5" Tall

Note: Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment and Window Frame Holding Arms under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Extended US Warranty: 1 year limited warranty on defects in materials and workmanship.

Non-US Warranty: 30 days parts and labor.

Note: 3 piece set comes with one (1) base adapter window and two (2) clamping windows. Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment. Chassis shown in photos sold separately. Click here to view the compatible chassis or view it under Recommended Accessories below.

Brother HoopTech SAPR44, 4x4" Window Frame Attaches to Gator Clamp Chassis Base Unit for Brother PR600 PR620 PR650 PR1000 and Babylock EMP BMP ENT BNT

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

Note: 3 piece set comes with one (1) base adapter window and two (2) clamping windows. Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment. Chassis shown in photos sold separately. Click here to view the compatible chassis or view it under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

Note: 3 piece set comes with one (1) base adapter window and two (2) clamping windows. Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment. Chassis shown in photos sold separately. Click here to view the compatible chassis or view it under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

Non-US Warranty: 30 days parts and labor.

Note: 2 piece set comes with one clamping window and base adapter window. Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment. Chassis shown in photos sold separately. Click here to view the compatible chassis or view it under Recommended Accessories below.

5" Wide x 3" Tall

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

Note: 3 piece set comes with one (1) base adapter window and two (2) clamping windows. Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment. Chassis shown in photos sold separately. Click here to view the compatible chassis or view it under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

Use Clamps when you want Faster Positioning Without Obstacles! Clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Holds products steady, and never leaves a hoop burn. Perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

*Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment and Window Frame Holding Arms under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

Use Clamps when you want Faster Positioning Without Obstacles! Clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Holds products steady, and never leaves a hoop burn. Perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

*Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment and Window Frame Holding Arms under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

*for Brother PR1000, PR600 Embroidery Machines, Requires SAPRB6* Requires your existing or new purchase of Brother HoopTech SAPRB6 PR600 Chassis Attachment and Window Frame Holding Arms under Recommended Accessories below.

No more hooping! Clamp it with HoopTech and get faster positioning without obstacles.

Perfect for those times when you just can’t hoop an item for fear of hoop burn, or fabric thickness, or many other reasons!

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Brother PR & Babylock
Rail Mounted Clamping System
Designed to fit on Brother PR600 / 620 / 650 / 1000 and Babylock models.

Clamping System Features

Single lever opens, closes and locks the clamp.

(8) interchangeable window sizes to choose from.

Mounts directly to machine drive bar for positive attachment.

All metal construction, powder coated aluminum & stainless steel.

The clamp automatically adjusts to different fabric thickness.

Clamping action does not leave “hoop burns”

Clamp stays on the machine while loading and unloading.

Non-US Warranty: 30 days parts and labor.

The Quick Change is a set of interchangeable sewing windows designed to be used with a pressure sensitive or sticky backing.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

*Bracket on photos may differ in appearance depending on your brand and model machine

Non-US Warranty: 30 days parts and labor.

The HOOP TECH "Square Solution" hoops offers two advantages over round hoops (1) a larger sewing field verses a round hoop of the same size, because of the additional area in the corners, and (2) the ability to see the alignment of the garment with the straight sides of the hoop.

HOOP TECH hoops feature:
- Large easy to grip adjusting screw.
- Double height frame
- Rounded corners on the hoop & frame to reduce "hoop burn"

This product is made to fit the Brother PR600/620/650 6 Needle Embroidery Machines.

HOOP TECH hoops are available for all industrial embroidery machines by simply attaching arm adapters designed to fit your machine. Please contact us if you are interested in purchasing EMS Hoop Tech Hoops for other machines.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

Hoop Tech 599322 4.5"x6 " Window Frame for ICTCS 2 Clamp Base

Non-US Warranty: 30 days parts and labor.

This was the Brother Original 22x22x32"High, All Metal Roller Table Stand, 8 Feet on Floor, now modified for Brother PRS100, PR620, PR650, PR655, PR670, PR1000, PR1050X, PR1055X, Babylock Alliance, EMP6, BMP8, BMP9, ENT10, BNT10, Etc. Embroidery Machines.

HOOP TECH was the DESIGNER and ORIGINAL producer of the machine stands for the PR-600 machines. The rugged design, stability and ease of assembly has made it a standard in the industry. Features include, a large shelf, height adjustable framing gage support, lock down brackets to securely attach the machine to the stand, easy rolling casters and leveling pads on outrigger brackets for added stability. The heavy duty stand is all steel construction with a durable powder coat finish and is made right here in the United States.

The Hoop Tech Embroidery Machine Stand for Brother PRS100 PR600 620 650 1000 will be the best investment you can make for your Brother PR embroidery machine. The Hoop Tech Embroidery Machine Stand for Brother PRS100 PR600 620 650 1000 makes embroidering easier than ever before with your machine. The Hoop Tech Embroidery Machine Stand for Brother PRS100, PR600 620 650 1000 is made specifically for the Brother PRS100, PR600 620 650 and 1000. It is also compatible with Baby Lock 1, 6 and 10 needle embroidery machines.

• This machine stand measures 22"x22"x32"
  
• Stand on Wheels has been constructed exclusively for the PR600 and PR620, and measures 22" wide, 22" deep, and 32" tall
  
• Four 2 1/4" diameter adjustable foot pad stabilizers to reduce vibration.
  
• Has 4 heavy duty large rolling casters plus 4 more stabilizer feet, a total of 8 feet which reduce vibration.
  
• Has shelf underneath for extra hoop storage
  
• Perfect mobility for moving around the room or rolling into a building.
  
• Ships RTA Ready to Assemble
  
  Hoop Tech Stand Features:
  
• Easy to assemble
  
• All steel construction
  
• Rugged powder coat finish
  
• Large shelf area
  
• 2-Lock down brackets
  
• Easy rolling casters
  
• Leveling feet for stability
  
• Made in America
  
  Compatible with:
  Brother PRS100 Persona
  Brother PR600
  Brother PR600II
  Brother PR620
  Brother PR650
  Brother PR655
  Brother PR670
  Brother PR1000
  Brother PR1050X
  Babylock BNAL Alliance
  Baby Lock 6 Needle Models
  Baby Lock 10 Needle Models

Non-US Warranty: 30 days parts and labor.

Non-US Warranty: 30 days parts and labor.

This was the Brother Original 22x22x32"High, All Metal Roller Table Stand, 8 Feet on Floor, now modified for Tajima Juki 8 Needle Commercial Embroidery Machine,

HOOP TECH was the DESIGNER and ORIGINAL producer of the machine stands for the PR-600 machines. The rugged design, stability and ease of assembly has made it a standard in the industry. Features include, a large shelf, height adjustable framing gage support, lock down brackets to securely attach the machine to the stand, easy rolling casters and leveling pads on outrigger brackets for added stability. The heavy duty stand is all steel construction with a durable powder coat finish and is made right here in the United States.

The Hoop Tech Embroidery Machine Stand will be the best investment you can make for your Brother PR embroidery machine. The Hoop Tech Embroidery Machine Stand makes embroidering easier than ever before with your machine.

• This machine stand measures 22"x22"x32"
  
• Stand on Wheels has been constructed exclusively for the PR600 and PR620, and measures 22" wide, 22" deep, and 32" tall
  
• Four 2 1/4" diameter adjustable foot pad stabilizers to reduce vibration.
  
• Has 4 heavy duty large rolling casters plus 4 more stabilizer feet, a total of 8 feet which reduce vibration.
  
• Has shelf underneath for extra hoop storage
  
• Perfect mobility for moving around the room or rolling into a building.
  
• Ships RTA Ready to Assemble
  
  Hoop Tech Stand Features:
  
• Easy to assemble
  
• All steel construction
  
• Rugged powder coat finish
  
• Large shelf area
  
• 2-Lock down brackets
  
• Easy rolling casters
  
• Leveling feet for stability
  
• Made in America
  
  

Non-US Warranty: 30 days parts and labor.

Sizes Include:

• 4.5" x 2"
  
• 4.5" x 2.5"
  
• 4.5" x 3"
  
• 4.5" x 4.5"
  
• 6.5" x 4.5"
  
• 4" x 11"
  
• Back of hat frame - 6.5" x 3.25"
  
  NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

The Quick Change is a set of interchangeable sewing windows designed to be used with a pressure sensitive or sticky backing.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

*Bracket on photos may differ in appearance depending on your brand and model machine

Non-US Warranty: 30 days parts and labor.

The Koozie Clamp is a heavy duty screw activated clamp specially designed to hold neoprene koozie drink covers for embroidery. This clamp will hold the stretchy material securely while it is stretched over the sewing arm during sewing. The Koozie has a big 2-3/4” x 3” sewing window for a large design.

CLAMP WILL ADAPT TO FIT THE FOLLOWING TYPES OF SINGLE-HEAD EMBROIDERY MACHINES:
BABYLOCK BMP/ENT
BARUDAN
BROTHER
PR600/620/650/1000
MELCO
SWF
TAJIMA
TOYOTA

The HOOP TECH SOLO CUP Koozie Clamp is designed to allow embroidery on the popular Koozie. Its exceptional grip strength will hold the Koozie in place during embroidering. The clamp body is rail mounted, (it attaches directly the drive rail of the panagraph - same as a cap driver) to ensure maximum rigidity on the machine.
The window size is 2 3/4" wide X 3" deep. The window size is designed small enough to fit down into most Koozies and still have an adequate sewing field for logos, monograms, names, etc.
The upper and lower clamping frames have an aggressive non-slip surface to hold leather and nylon secure during sewing.


• MOUNTS DIRECTLY TO MACHINE DRIVE BAR FOR POSITIVE ATTACHMENT.
• ALL METAL CONSTRUCTION, POWDER COATED ALUMINUM & STAINLESS STEEL.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

The HOOP TECH "Square Solution" hoops offers two advantages over round hoops (1) a larger sewing field verses a round hoop of the same size, because of the additional area in the corners, and (2) the ability to see the alignment of the garment with the straight sides of the hoop.

HOOP TECH hoops feature:
- Large easy to grip adjusting screw.
- Double height frame
- Rounded corners on the hoop & frame to reduce "hoop burn"

This product is made to fit the Brother PR600/620/650 6 Needle Embroidery Machines.

HOOP TECH hoops are available for all industrial embroidery machines by simply attaching arm adapters designed to fit your machine. Please contact us if you are interested in purchasing EMS Hoop Tech Hoops for other machines.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

The HOOP TECH "Square Solution" hoops offers two advantages over round hoops (1) a larger sewing field verses a round hoop of the same size, because of the additional area in the corners, and (2) the ability to see the alignment of the garment with the straight sides of the hoop.

HOOP TECH hoops feature:
- Large easy to grip adjusting screw.
- Double height frame
- Rounded corners on the hoop & frame to reduce "hoop burn"

This product is made to fit the Brother PR600/620/650 6 Needle Embroidery Machines.

HOOP TECH hoops are available for all industrial embroidery machines by simply attaching arm adapters designed to fit your machine. Please contact us if you are interested in purchasing EMS Hoop Tech Hoops for other machines.

NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.

"I had two trunk organizers to embroider and no way it was going to happen with the hoops I had.
Your hoop system was fantastic! Being able to just clamp it down in the frame was fantastic." Melba M. Meridian MS

Hoop Tech is the perfect choice for embroidering smaller difficult to hoop items such as purses, back packs and small totes. Expand your product offerings and stay ahead of your competition! Open the world of embroidery to items that previously were impossible to sew on: leather portfolios, tote bags, heavy and thick items and more– the possibilities are endless. Rail Mounted Clamping System. Designed to fit on Brother PR600 / 620 / 650 / 655, 670 1000's and Babylock models. Includes an 8×5 and 11X5 window

Clamping System Features:

• Single lever opens, closes and locks the clamp.
  
• (2) interchangeable window sizes to choose from.
  
• Mounts directly to machine drive bar for positive attachment.
  
• All metal construction, powder coated aluminum & stainless steel.
  
• The clamp automatically adjusts to different fabric thickness.
  
• Clamping action does not leave “hoop burns”
  
• Clamp stays on the machine while loading and unloading..
  
  The base unit, or Chassis, holds the two pieces (bottom and top) of the clamping Window in place with just the twist of a knob!
  
  Includes 11" x 5" Window and 8" x 5" Window Set
  
  Use Clamps when you want Faster Positioning Without Obstacles! Clamp over heavy seams, velcro, zippers, and other elements that make it almost impossible to squeeze into a hoop. Holds products steady, and never leaves a hoop burn. Perfect for leather, lunch bags, fanny packs, canvas totes, garment bags, gym bags, and more.
  
  NOTE: When using hoops on your Brother machine that are non-Brother hoops you may have to do a trial layout. Make sure the needle or foot will not hit the frame when it is sewing.

Non-US Warranty: 30 days parts and labor.